Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Read these messages carefully. The following precautions are suggested to help prevent accidents. Read and practice the following precautions before operating this equipment. Equipment should be operated only by those who are responsible and have been properly instructed. 1. Read all operating and maintenance instructions before operating or servicing mixer. Test run empty prior to actual use. 2. A mixer is only as safe as its operator. Give complete and undivided attention to the operation of the mixer. 3. Know how to stop the mixer and the engine instantly. 4. Always have all guards and safety devices attached and in place before operating mixer. Close engine housing during operation. 5. Keep inexperienced and unauthorized people away from the mixer at all times. 6. Never leave the mixer unattended while it is running. 7. Shut off engine or disconnect the electric motor before making any adjustments or putting hands or tools in the drum. 8. Do not overfill the drum. Do not exceed the mixer’s rated capacity. 9. Do not smoke while refueling the engine. Shut off the engine and allow it to cool before refueling. Do not spill fuel. 10. Block mixer wheels when mixing. 11. Use safety chains while towing mixer. 12. Keep the mixer in good operating condition. Loose or damaged parts are dangerous. 13. Avoid loose clothing that could get caught in moving parts or on control levers. 14. Do not add material to the drum while stopped. Start the drum before adding material. 15. Keep all warning, caution and safety instruction labels in good condition. Replace missing, damaged or illegible labels. 4 TOWING & SAFETY CHAINS: For transporting the mixer, slide the tow pole out as far as possible and insert the locking pin. When operating the mixer, slide the tow pole in and lock it in place. Make sure drum is locked in position and engine housing is closed and secured. Cross the safety chains under the tow pole and fasten them to the tow vehicle. (fig.1) NOTE! Safety chain length may need to be altered for proper connection to tow vehicle. Reposition the hooks, DO NOT cut chain. Allow enough slack to permit proper vehicle turning while keeping chains snug enough to prevent tow pole from contacting the ground in case the hitch uncouples. PRIOR TO START UP: 1. Examine the mixer carefully to make sure there was no damage during shipment or since the last use. Report any damage immediately to the transportation company. Repair any damage before using the mixer. 2. Check for free rotation of the mixer drum yoke by rotating the drum through one complete dump-charge-dump cycle. Make sure no foreign objects or tools are in the drum before starting the motor. 3. Check the engine oil. Fill as required. Refer to the engine manual for oil specifications. 4. Fill the fuel tank with fresh, clean fuel. Refer to the engine manual for fuel specifications. 5. Grease all fittings as called out in the lubrication specifications. 6. Start the motor and check for smooth operation of the drum, ring gear, and pinion. Note: After initial 10 hours of operations, check chain/belts for proper tension and sprockets/pulleys for alignment. Check these items monthly to prevent premature wear/failure. LUBRICATION Use lithium based grade 2 multi-purpose grease. Drum Shaft Tube: Drum shaft lubrication can be performed by removing the 1/8” pipe plug (item 4, fig3) and installing the appropriate grease fitting. Greasing should be done yearly. Yoke Bearing Hangers: Yoke bearing hangers are located on the yoke ends and are equipped with grease fittings. These bearings should be greased weekly. Wheel Bearings: Grease wheel bearings once per year. Thoroughly remove old grease from bearings and spindle before repacking. Pack bearings . to 2/3 full to prevent overheating. 5 Drum Tilt Brake Bearing: The brake bearing casting is located near the front of the mixer and should be greased weekly. Handwheel Bearing: The handwheel hub bearing is located on the front of the mixer, behind the handwheel. This bearing should be greased weekly. WARNING: DO NOT GREASE BRAKE BAND OR OUTER BRAKING SURFACE OF TILT GEAR. Jack Shaft Bearings: Pillow block style bearings are used on the drive train counter shaft. These bearings should be greased weekly. Drive Chain: The drive chain should be lubricated monthly with SAE #20 or SAE #30 oil. Apply the oil between the side plates. Engine/Motor: Refer to the manufacturer’s engine or motor operating instructions for all maintenance and lubrication requirements and instructions. LUBRICATION FREQUENCY CHART: # ITEM FREQUENCY FIGURE CODE PLACES 1 Yoke Bearing Casting weekly 3 grease 2 2 Handwheel Hub weekly 4 grease 1 3 Drum Tilt Brake Bearing Casting weekly 4 grease 1 4 Drive Shaft & Jackshaft weekly 4 grease 1 5 Drum Shaft Tube yearly 3 grease 1 6 Wheel Bearings yearly 1 grease 2 7 Drive Chain monthly 4 oil 1 MIXING INSTRUCTIONS: 1. Start the drum rotating. 2. Add water. 3. Add cement and one shovelful of coarse aggregate. The coarse aggregat...
Otros modelos de este manual:Mezcladoras - 600CM (181.35 kb)