Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
Turn the SPEED dial pointer to STIR. 2. Apply power to the mixer. With the bowl locked into place, the bowl support all the way up and bowl guard closed, momentarily run the machine by pushing the START and then STOP buttons. 3. Verify that the motor is turning counterclockwise (Fig. 2). If not, reverse any two lead wires. 4. Verify that the bowl lift actuator raises and lowers per the switch direction arrows. Fig. 2 – 6 – OPERATION WARNING: MOVING AGITATOR IN BOWL, KEEP HANDS, CLOTHING AND UTENSILS OUT WHILE IN OPERATION. DO NOT USE WITHOUT INTERLOCKED GUARD. The Legacy® mixer is equipped with SmartTimerTM controls and a power bowl lift. Other operating parts (Fig. 3) and their functions are described throughout the Operation section. The Wire Cage must be in position or the mixer will not operate. The bowl must stay in the locked position on the Bowl Support or the mixer will not operate. If the Bowl Support is not all the way up (mix position), the mixer will not operate unless the Start button is pressed and held. If the Bowl Support is not at the mix position and the START button is pressed and held, the mixer will operate only in stir speed. Fig. 3 – 7 – STANDARD CONTROLS Model HL800 and HL1400 (With Four Mix Speeds Plus Stir Speed) Fig. 4 Mixer Speeds (Model HL800 and HL1400) STIR (Slow) This speed is for incorporating ingredients at the start of each mixing process. SPEED 1 (Low) This speed is for heavy mixtures such as pizza dough, heavy batters and potatoes. SPEED 2 (Medium-low) This speed is for mixing cake batters, mashing potatoes and developing bread dough. SPEED 3 (Medium-high) This speed is for incorporating air into light batches, as well as finishing whipped items. SPEED 4 (High) This speed is for maximum and accelerated air incorporation into light batches. – 8 – PROGRAMMABLE RECIPE TIMER (OPTIONAL) Fig. 5 Timer Specifications (Model HL800 and HL1400) • Maximum number of programmable recipes: 9 recipes. • Maximum number of steps allowed for each recipe: 6 steps. • Maximum time allowed for each step in a recipe: 30 minutes. For additional information on use of the programmable recipe timer, refer to pages 14 through 19. – 9 – BOWL PLACEMENT NOTE: The bowl must be installed onto the bowl support before the agitator is installed. To Install BOWL PLACEMENT NOTE: The bowl must be installed onto the bowl support before the agitator is installed. To Install . Fully lower the bowl support. 2. Position bowl so the alignment pins on the left side of the bowl support fit in the holes in the bowl. 3. Swing the bowl into the locked position on bowl support (Fig. 6). To Remove 1. Lower the bowl by pressing and holding the down arrow on the bowl switch. 2. Unlock bowl and swing out slightly from locked position 3. Open wire cage and remove agitator. AGITATOR To install an agitator, the bowl must be on the bowl support and fully lowered. To Install 1. Open the wire cage. 2. Place the agitator inside the bowl and line up the horizontal slot on the agitator with the agitator shaft pins. 3. Slide the agitator up the agitator shaft until it stops and latches (Fig. 6). To Remove 1. Open the wire cage. 2. Lower the bowl by pressing and holding the down arrow on the bowl switch. 3. Hold the agitator and pull the plunger of the agitator out (Fig. 7). Slide agitator down off the agitator shaft. Fig. 6 Fig. 7 – 10 – POWER BOWL LIFT POWER BOWL LIFT Fig. 8 To raise the bowl, the bowl must be in the locked position. Push and hold the up arrow on the bowl switch. To lower the bowl, push and hold the down arrow on the bowl switch. To Raise the Bowl While Mixing To raise the bowl while the agitator is mixing the product (when required by recipe or when using the Bowl Scraper Attachment): 1. Close the wire cage, then select a mixing speed on the SPEED dial. 2. Select a count-down time or HOLD for continuous count-up mixing. 3. While pressing and holding the up arrow on the bowl switch, press and hold the START button. The mixer runs only in stir speed while the bowl is rising. 4. When the bowl reaches the mix position, release the START button. The mixer automatically changes to the selected mixing speed. NOTE: Mixing speed and time can be adjusted any time during the mixing operation without stopping the mixer. – 11 – PREPARE FOR MIXING 1. Open the wire cage. 2. Place the mixing bowl on the bowl support. 3. Pour ingredients into the bowl. 4. Swing the bowl back to the locked position. 5. Place the agitator inside the bowl, then attach it to the agitator shaft. 6. Return the wire cage to front-center position. 7. Push and hold the up arrow on the bowl switch until the bowl reaches the mix position and stops. 8. The mixer is now ready for mixing. (See Timer Operation.) Fig. 14 TIMER OPERATION Using the Count-Up Mode (Continuous Mixing) 1. Turn the SPEED dial to select a mix speed (the SPEED setting can be changed at any time during the mixing operation). NOTE: STIR is to be used for incorporating ingredients. Do not use t...
Otros modelos de este manual:Mezcladoras - HL800 (2.59 mb)
Mezcladoras - ML-134343 (2.59 mb)
Mezcladoras - ML-134354 (2.59 mb)