Votos - 5, Puntuación media: 4 ( )

Fabricar: Husqvarna Tamaño del archivo: 3.37 mb Nombre del archivo: Idioma del manual:

• Keep operation area clear of all persons. • DO NOT overreach or stand on unstable support. Keep good footing and balance at all times. • Follow the maintenance instructions specified in the manual. Risk of injection or ! WARNING severe injury. Keep clear of nozzle. DO NOT discharge streams at persons. This product is to be used only by trained operators. ALWAYS remove lance from gun before cleaning debris from tip. • Keep clear of nozzle. NEVER direct high pressure spray at a person, animal, or yourself. • ALWAYS wear safety glasses or goggles and protective equipment (hearing protection, gloves, rubber boots, protective clothing) when operating or performing maintenance. • NEVER put hand or fingers over the spray tip while operating the unit. • NEVER try to stop or deflect leaks with any body part. DO NOT use ! WARNING pressure that exceeds the operating pressure of any of the parts (hoses, fittings, etc.) in the pressurized system. Ensure all equipment and accessories are rated to withstand the maximum working pressure of the unit. Explosion hazard. ! WARNING • NEVER spray flammable liquids or use pressure washer in areas containing combustible dust, liquids, or vapors. • NEVER operate this machine in a closed building or in or near an explosive environment. • DO NOT remove fuel tank cap or fill fuel tank while engine is hot or running (allow engine to cool two minutes before refueling). ALWAYS fill the tank slowly. • NEVER disconnect the high pressure discharge hose from the machine while the system is pressurized. To depressurize machine, turn power and water supply off, then press the gun trigger 2-3 times. • NEVER permanently engage the trigger mechanism on the gun. • NEVER operate the machine without all components properly connected to the machine (handle, gun/wand assembly, nozzle, etc.). Keep hose away from sharp ! CAUTION objects. Bursting hoses may cause injury. Examine hoses regularly and replace if damaged. DO NOT attempt to mend a damaged hose. Equipment damage. NOTICE • ALWAYS turn water supply “ON” before turning pressure washer “ON.” Running pump dry causes serious damage. • DO NOT operate the pressure washer with the inlet water screen removed. Keep screen clear of debris and sediment. • NEVER operate pressure washer with broken or missing parts. Check equipment regularly and repair or replace worn or damaged parts immediately. 6 — English SAFETY GUIDELINES • Use only the nozzle supplied with this machine. • NEVER leave the wand unattended while the machine is running. • NEVER tamper with the engine governor or attempt to alter factory settings. Altering factory settings could damage the unit and will void the warranty. • ALWAYS hold gun and wand firmly when starting and operating the machine. • NEVER allow the unit to run with the trigger released (off) for more than two minutes. Resulting heat buildup will damage the pump. • NEVER store the pressure washer outdoors or where it could freeze. Freezing temperatures can seriously damage the pump. • Release the trigger when changing from high to low pressure modes. Failure to do so could result in damage to the nozzle. English — 7 PRE-OPERATION UNPACKING Remove the equipment and all parts from the carton. The carton should contain the following. • One pressure washer (pump, engine, cart base). • One cart handle assembly. • One spray gun. • One lance. • Two spray tips for Model 5525PW Five spray tips for Models 1335PW, 6026PW and 9030PW • One high pressure hose. • One pack of nuts, bolts, and manuals. • One bottle of engine oil. If any parts are missing, Please contact your Husqvarna dealer. After unpacking the product, inspect it carefully for any damage that may have occurred during transit. Make sure to tighten fittings and bolts before using the pressure washer. DO NOT operate the unit if it’s ! WARNING damaged during shipping, handling, or use. Damage could result in bursting and cause injury or property damage. ASSEMBLY Use 1/2” (13 mm) wrench to assemble pressure washer. On model 5525PW use two adjustable or 7/16” wrenches. 1. Slide the handle assembly over the lower legs of the cart base. Use the standard nut and bolt to secure the legs. See Figure 1. Figure 1 - Assemble Handle 2. On models 5525W and 6026W connect clear plastic hose to hose barb on detergent tank (See Figure 2). On models 1335PW and 9030PW connect to brass barb on pump (See Figure 3). Figure 2 - Connect detergent hose to detergent tank Figure 3 - Connect detergent hose to brass barb 3. Secure garden hose (not included) to the inlet connection on pump (See Figures 4 and 5). Figure 4 - Secure garden hose Garden Hose High Pressure Hose 8 — English PRE-OPERATION 4. Connect the high pressure hose to the pump outlet (See Figure 5). Garden Hose High Pressure Hose Figure 5 - Connect high pressure hose to pump 5. Attach the lance with nozzle to the gun (See Figure 6). Figure 6 - Attach lance to gun 6. Install quick connect tip by pulling back on collar and pressing in tip. R...

Descargar ahora

Introduzca dos números de la imagen: