Votos - 3, Puntuación media: 3.7
(
)
)
|
Fotos y especificaciones BenQ FP531 |
Resumen del manual
A small window will pop up. Select the “Monitor” tab in the new window and then click “Properties”. 2. Select “Driver” tab and then click “Update Driver…” 3. The “Hardware Update Wizard” will pop up. Then click “Next”. 4. Select “Don't search. I will choose the driver to install” and then click “Next”. 5. In the next window, click “Have Disk…”, an “Install From Disk” window will pop up. Click “Browse”. The “Locate File” window will pop up. 6. Select your driver and then click “Next”. 7. The new drivers are now installed to your computer. Click “Finish” to exit installation. How to Install Your Monitor's Software 13 Choosing the Best Picture Resolution Due to the nature of LCD display technology, the picture resolution is always fixed. The best picture possible for your FP531 is achieved with a resolution of 1024 x 768. This is called "ative Resolution” or maximal resolution - that is, the clearest picture. Lower resolutions are displayed on a full screen through an interpolation circuit. However flaws do occur with the interpolated resolution. So if you want to have all the advantages of LCD technology you must use the native resolution. If you are using Windows 98/2000/ME or XP you can change the picture resolution as follows: 1. Double-click the “Display” icon in the Control Panel. 2. From the “Display Properties” window, select the “Settings” tab. You can alter the resolution by using the slider on the right-hand side. 14 Choosing the Best Picture Resolution 3. Select a resolution of 1024x768. Then click “Apply”. 4. In the subsequent windows, press “OK” and “Yes” 5. You can now close “Display Properties”. Choosing the Best Picture Resolution 15 How to Choose the Right Refresh Rate You don't have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer. There is a table with the factory modes in this user's guide. Youc an choose 60, 70 and 75 Hertz, (but not 72Hz) for the native resolution of 1024 x 768. In Windows 98/2000/ME/XP you can change the refresh rate as follows: 1. Double click the “Display” icon in the Control Panel. 16 How to Choose the Right Refresh Rate 2. From the “Display Properties” window, select the “Settings” tab. Click the “Advanced...” button in the bottom right corner. How to Choose the Right Refresh Rate 17 3. Select the “Adapter” tab. The refresh rate selection field is located in the center at the bottom of the window. 4. Choose a refresh rate from the table with the factory modes, which can be found in the user's guide, and select this in the settings field. 5. In the subsequent windows press “Change”, “OK” and “Yes”. 6. You can now close “Display Properties”. 18 How to Choose the Right Refresh Rate How to Set the Picture Optimization The easiest way to obtain an optimal display is to use the ikeyfunction. Press the “ikey” on the control panel and the monitor will adjust automatically. If you are still not satisfied with the result, you can still adjust the image manually. 1. Run the test program auto.exe from CD-ROM; this is the best way to observe possible changes. You can also use any other image, such as the desktop of your operating system. However, we recommend that you use auto.exe. As you run auto.exe, a test pattern emerges. 2. Press “Enter” on control panel to access OSD. 3. If there is vertical noise observed, press ..or .. key to select “Geometry” and press “Enter” key. Then press ..or ..key to select “Pixel Clock” and also press “Enter” key again. Now, press..or .. key to adjust the monitor untill the noise disappears. 4. If there is horizontal noise observed, press t or u key to select “Geometry” and press “Enter” key. Then press..or .. key to select “Phase” and also press “Enter” key again. Now, press .. or .. to adjust the monitor untill the noise disappears. To make sure the “iKey” function performs well, you have to use one of the supported modes. If the “iKey” does not work properly and the “NON PRESET MODE” message is on the OSD, it means you are not using one of the supported modes. Please set your computer to use one of the supported modes. You will find a list of supported modes in this manual. How to Set the Picture Optimization 19 88 How to Adjust Your Monitor A Look at the Control Panel There are 6 keys for user's control including “iKey”, “Exit”, “Enter”, “<” and “>” key and a power swith. The following descriptions are the introduction of these keys & switch. 1. “Power”: Turn the power on or off. 2. “iKey” : Adjust vertical position, phase, horizontal position and pixel clock automatically. 3. “Exit” key: Back to previous menu or exit OSD. 4. “Enter” key: Activate OSD, enter sub menu, select items, confirm selection and hot key for OSD Lock. 5. .. (Left) key: For Left/Decrease adjustment. Left key is the hot key for Contrast. 6. .. (Right) key: For Right/Increase adjustment. Right key is the ...