Votos - , Puntuación media:
(
)
)
Fabricar: Audiovox
Tamaño del archivo: 216.12 kb
Nombre del archivo: 5bf598df-552f-40fc-81b9-b556ca4bd07b.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
Using a Sharpie™ marker or similar marking pen, mark headrest material along the interior of the trim collar. Remove the trim collar and mark an “X” from corner to corner as shown -3 Using the utility knife, cut the headrest material along the “X” lines. Do not cut the material along the other lines at this time. This will leave you with an “X” cut as shown. Pull the flaps up and cut the foam beneath the material to the proper depth. Cut all four sides of the foam. Using your fingers, tear the foam out of the headrest leaving a recess where the shell will be inserted. At this point you will need to install the harness up through the area into the recess. It may be helpful to follow one of the posts and tie wrap it to the post for restraint. -4 Lay the flaps of headrest material down into the recess and insert the clamshell into the recess. Check for fit. If it does not fit properly, you may need to remove some more foam. NOTE: The clamshell will need to be secured to the headrest, either by using tie straps, screws, ect.. If used, remove the clamshell and insert the IR transmitter and plug into the IR transmitter board. Reinsert the clamshell into the recess and secure using tie wraps or screws. Plug the remaining connector into the monitor. Turn the monitor around and insert it into the clamshell housing. Snap into place. Connect the wiring to the video system and test. -5 The supplied Release Key is for removing monitor from housing. Refer to the drawing below. MONITOR SURFACE MOUNTING: 1. Slide the monitor onto the mount S2 and tighten using the fastener. 2. Firmly attach surface mount to a flat surface and adjust the viewing angle of the monitor by loosening the fastener on the side. Tilt the monitor for a good viewing angle and retighten the fastener. Fastener -6 LCM500NP SYSTEM WIRING DIAGRAM 1.) Make sure the LCM500NP has been installed properly, as described in the procedures as stated on pages 2, 3, and 5. 2.) Plug the 15 pin connector into the jack labelled -15 pin to MONITOR on the AVX-6865 Interconnection Box. 3.) Connect the 2 pin connector to the jack labelled IR POWER output on the AVX-6865 Interconnection Box. 4.) Connect the video source to the jack labelled VIDEO IN 1 on the AVX-6865 Interconnection Box. 5.) Connect the audio source to the 2 RCA connectors that are incorporated in the Monitor Cable Assembly (for optional audio connection). 6.) Power Connections: a) Red (ACC): Connect to switched 12Vdc. b) Yellow (Batt): Connect to constant 12Vdc. c) Blue (Remote Out): 12Vdc output. d) Black (Ground): Connect to chassis ground. -7 Controls and Indicators Monitor Panel Controls Controls and Indicators Monitor Panel Controls -8 Remote Control Unit Remote Control Unit Controls Remote Control Unit Remote Control Unit Controls -9 Remote Control Unit Controls Continued Press the to the desired setting KEY KEY Press the to the desired setting Press the MODE key to select the desired video source input (Input 1 or Input 2) -10 Display Mode 1. Press MENU to get the On Screen Display (OSD). 2. Select FORMAT. 3. Press the or the to switch the screen aspect ratio. FULL: 16:9 picture is fully displayed. ZOOM: Picture is stretched vertically and horizontally. CINEMA: Picture is displayed with uniform horizontal enlargement. NORMAL: When 4:3 pictured is displayed on a wide screen, black bands appear on the right and left of the picture -11 OPERATING INSTRUCTIONS 1. POWER ON/OFF/MODE Press the POWER button to turn power on. Pressing the POWER button again momentarily will change video inputs. Press the for NTSC input. Press the for PAL input. Press and hold the POWER button for three seconds to turn power off. 2. Scroll Up Button This button is used to increase selected menu items (Brightness, Contrast, Color, Tint, [NTSC] Only) This button will also switch selected items (DIM, RESET, FORMAT). 3. Scroll Down Button This button is used to decrease selected menu items (Brightness, Contrast, Color, Tint, [NTSC] Only) This button will also switch selected items (DIM, RESET, FORMAT). 4. MENU Button Press the MENU button once to display the menu On Screen Display. Press the button again until the desired menu item is highlighted. Use the or to adjust or switch the selected item. The On Screen Display menu will disappear if no buttons are pressed for four seconds. -12 MONITOR SPECIFICATIONS 1. Type : TFT Active Matrix LCD 2. Display Screen Size : 4.3 x 2.5 inches (109.2 x 63.5) (W x H) 3. Resolution: 1200 (W) x 234 (H) 4. Pixels: 280,800 5. Back Light : Cold Cathode Fluorescent Lamp 6. Power Source : +12 VDC 7. Power Consumption : 510 mA, 7W 8. Connection Terminals : 1-12 Vdc Constant -Yellow 1-12 Vdc Switched -Red 1- Ground-Black 1-12 Vdc Output -Blue 2-Video Inputs-RCA 1-Video Output-RCA 2- Audio L/R In-RCA 9. Operating Temperature : 32°F – 104°F (0°C – 40°C) 10. Storage Temperature : -4°F – 176°F (-20°C – +80°C) 11. Monitor Cabinet : 5.3 in x 3.3 in x 1 in (WxHxD) Dimensions (134.6 x 83.2 x 25.4 mm) 12. Weight...
Otros modelos de este manual:Monitores - LCM500NP (216.12 kb)