Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
10.Recommended Adjustment To reduce the risk of “image persistence”, please adjust the following items based on the application being used: “POWER SAVE”, “PANEL SAVING”, “DATE AND TIME”, “SCHEDULE”. User Manual BDL3215E / BDL4225E 15 11.To prevent the main power switch from being changed To prevent the possibility of main power switch being carelessly pushed, please attach the main switch cover (accessory) onto it. NOTE: Remove main power switch cover to turn off the display. Screw Main switch cover User Manual BDL3215E / BDL4225E Install the LCD Monitor in Portrait Mode BDL3215E/BDL4225E can be installed in portrait position, under the following conditions: Caution: Portrait mode is effective only when wall-mounted or ceiling-mounted. The table stand can not be used for the monitor in portrait position. Placing the monitor in portrait position, will shorten the average life of the LCD backlight. Operational Environment (Temperature) shall be limited, as shown below: Operational Environment Temperature 5 - 35 °C / 41 - 95 °F Humidity 20 - 80 % (Without condensation) Please orientate the monitor in the direction shown as the right figure: Do not place monitor in landscape in any other manner. How to set-up 1. Remove the table stand if they are attached. 2. The “ ” logo should be on the LEFT side when facing the monitor. Clockwise Counterclockwise 9090 How to Remove the Logo for landscape mode? 1. Prepare a piece of paper with a cutting area of logo as a protector to prevent the front bezel from scratching. 2. Using a knife, carefully remove the logo sticker with the paper placing beneath. 3. Tear off the logo sticker. 1 2 3 How to Use the Logo Guider for Portrait Mode? (a) Before applying, make sure the guider is well shaped. The “PHILIPS” sticker attached on the end of it could be folded back as figure (a). (b) Turn back the logo end of the guider and remove the sticky tape of the logo. (c) Slide the logo guider along the short side of the front bezel as figure c & then return the logo end of the guider back to the right side. (d) With your left hand fixing the guider, scrunch the logo by your right hand to make it stuck firmly on the front bezel. (e) Remove the guider and leave the logo over the front bezel. 16 User Manual BDL3215E / BDL4225E 17 Connectivity Before making connections: .................................................................................................................................................................... .... .... ............................................................................................................................................ Connectivity Diagram BDL3215E / BDL4225E BDL3215E / BDL4225E (Second monitor) DVD player HD or laser disk player VCR Equipment with Digital interface Personal computer User Manual BDL3215E / BDL4225E 18 Connecting to a Personal Computer As you finish the connection between the computer and the LCD monitor, you could play the contents in the computer and display them on the LCD monitor. Connecting the LCD Monitor to a Personal Computer To achieve this, apply the supplied VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin) to make connection .... between PC and LCD monitor (VGA IN connector). .... When connecting more than one LCD monitors to PC, apply another VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin; it’s commercially available) to make connection between LCD monitor (VGA OUT connector) and the other (VGA IN connector). .... The AUDIO IN 1, 2, 3 or HDMI can be connected for audio input using RCA cable. After choosing one of the AUDIO IN connectors, you might need to select AUDIO 1, 2, 3 or HDMI using the AUDIO SOURCE button on the remote control. HDMI (for audio) is selectable only when HDMI (for video) is selected. .... When connecting more than one LCD monitors to PC, apply RCA cable to make connection between LCD monitor (AUDIO OUT connector) and the other (AUDIO IN 1, 2, 3). HDMI source is not suitable for this case. BDL3215E / BDL4225E BDL3215E / BDL4225E To audio output PC or IBM compatible To analog VGA output Mini D-sub 15 pin RCA Mini D-sub 15 pin Second monitor User Manual BDL3215E / BDL4225E 19 Connecting to a Digital Interface Equipment Connections can be made between LCD monitor and other digital equipment that is equipped with a digital interface compliant with DVI (Digital Visual Interface) standard. Connect the LCD Monitor to a Computer with a Digital Output HDMI IN connector a .... ccepts HDMI cable. .... HDMI IN connector can receive video from HDMI source (applying a HDMI to HDMI cable) or DVI-D source (applying a HDMI to DVI cable) of PC. .... .................................................................................................................................................................. .... The AUDIO IN 1, 2, 3 or HDMI connector can be chosen to receive audio source. Select AUDIO 1, 2, 3 or HDMI from the AUDIO SOURCE button on the remote control. HDMI (for a...
Otros modelos de este manual:Monitores - BDL3215E/00 (2.81 mb)