Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Removing the transport locks Figure # (not on all models) Remove the four transport locks that are attached between the chest lid and the appliance. Place two of these transport locks on the holders provided for them on the rear of the appliance. This will maintain the minimum distance from the wall, meaning that the chest lid can be opened properly and that adequate ventilation is ensured. This means that the appliance will achieve its stated energy consumption. Location The ideal installation location is a dry, well-ventilated room. The installation location should not be subject to direct sunlight or be near a heat source such as a cooker, heating element, etc. If setting up the appliance next to a heat source is unavoidable, use a suitable insulating plate or observe the following minimum distances from the heat source: • 3 cm from an electric or gas cooker. • 30 cm from oil or solid fuel cookers. If the appliance is placed against the wall, there must be a minimum distance of 70 mm to the back panel and to the side panels. Floor surface The floor at the installation location must not buckle and you may have to reinforce the floor. Use a spirit level to align the appliance. Level out any unevenness in the ground using support spacers. en Note the room temperature and ventilation Ambient temperature The appliance is designed for a certain climate class. Depending on the climate class, the appliance can be operated at the following ambient temperatures. The climate class is specified on the rating plate, figure !/10. Climate class Permissible ambient temperature SN +10 °C to 32 °C N +16 °C to 32 °C ST +16 °C to 38 °C T +16 °C to 43 °C Note! The appliance can function within the ambient temperature limits of the specified climate class. If an appliance in the SN climate class is operated at lower ambient temperatures, damage to the appliance can be excluded up to a temperature of +5 °C. Ventilation Figure * The air on the appliance's back panel and side panels heats up. The heated air must be able to escape unimpeded. Otherwise, the refrigerating unit has to work harder, which increases the appliance's power consumption. Therefore: You must never cover or block the ventilation openings! en Connecting the appliance After setting up the appliance, wait for at least 1 hour before starting the appliance up. The oil contained in the compressor may have been displaced into the refrigeration system during transport. Before starting the appliance up for the first time, clean its interior (see section "Cleaning the appliance"). Electrical connection The socket must be near to the appliance and easily accessible after the appliance has been installed. The appliance conforms to protection class I. Connect the appliance to a 220-240 V/50 Hz alternating current supply using a socket with protective earthing conductor which has been correctly installed. The socket must be protected by a fuse with a rating of 10 A to 16 A. In the case of appliances operated outside of Europe, check whether the voltage and type of current specified conform to the values of your electricity grid. You will find this information on the rating plate, figure +. ! Warning The appliance must never be connected up to an electronic energy-saving socket. Sinusoidal-commutated and line-commutated inverters can be used with our appliances. Line-commutated inverters are used with photovoltaic systems that are connected directly to the national grid. Sinusoidal-communicated inverters must be used with standalone applications (e.g. on ships or mountain huts) that do not have a direct connection to the national grid. Getting to know the appliance Fold out the last page that contains the figures. These instructions for use apply for several models. Deviations between the figures are possible. Figure ! * Not available on all models 1.5 Control panel 6 Interior light * 7 Basket * 8 Storage compartment 9 Condensation drainage with drain plug 10 Rating plate 11 Pre-freezing compartment * 12 Removable separating wall * en Control panel Figure " 1 "eco" setting If the appliance is only partially filled (on appliances with a separating wall, maximum fill level is up to the "e" marking on the separating wall), this setting can be selected in order to save energy. 2 Temperature selector To adjust the freezer compartment temperature, turn the temperature selector using a coin. Position 1: Highest temperature Position 6: Lowest temperature 3 "alarm" indicator The red indicator lights up if the freezer compartment is too warm. 4 "power" indicator The green indicator lights up if the appliance is switched on. 5 "super" button This is used to switch the SuperFreezing function on and off. The yellow indicator lights up if the SuperFreezing function is switched on. en Putting the appliance into operation Switching on the appliance • Once it is connected, the appliance is switched on and the green indicator figure "/4 lights up. • If the red indicator lights up (figure "/...
Otros modelos de este manual:Congeladores - DF6034W2VV/02 (982.25 kb)