Votos - 2, Puntuación media: 4 ( )

Fabricar: Kenwood Tamaño del archivo: 2.08 mb Nombre del archivo: Idioma del manual:

The channel number will flash for about 3 seconds.The station name will flash for 7 seconds, and then remain lit. • If you want to listen to another station of that programme type, press the PTY button whilst the channel number or station name is flashing. The unit will look for the next station of that type. • “NOT FOUND” will appear for 4 seconds, if the requested programme type station is not found. 27 EN If you have selected the traffic programme : If you select traffic programme (TP) as the programme type in step 4 (on page 27) , to receive only radio station which broadcast traffic programmes, the TP will appear. (However, this does not necessarily mean that you will hear any traffic announcements at that time.) When a traffic announcement is actually being made, the TA will appear. (When both the TP and TA will appear, an announcement is being made.) P.CALL 4 1 . . To manually recall the stations stored in memory Press the P. CALL (4 1 or . .) button. • Each time the button is pressed, the station name will change. • After the station name had been displayed, the channel number will appear for 2 seconds. The frequency for that channel will appear for another 2 seconds and finally the station name will be displayed. 28 EN RDS DISPLAY (RDS display) (No RDS station display) RDS DISPLAY (RDS display) (No RDS station display) To switch the display Each time the RDS DISPLAY button is pressed whilst an FM station is tuned in, the display will switch as follows: When the station you are tuning in is not an RDS station or even if it is an RDS station but it is very weak signal, the display will change in the following order : Notes : • “NO PS”, “NO PTY”, or “NO RT” will flash for about 5 seconds, and then the frequency will be displayed. • The display can only be switched whilst tuned to the FM band. Notes for Radio text • The radio text for 8 characters will be displayed steadily for 4 seconds and then it will scroll across the display. • If you tune into a station which is not broadcasting any radio text, even if it is an RDS station, when you switch to the radio text position “NO RT” will be displayed. • Whilst radio text data is being received or when the text contents change, “RT” will be displayed. Notes for RDS operation If any of the following events occur, it does not mean that the unit is faulty. • “PS”, “NO PS” and a station name appear alternately, and the unit does not operate properly. • If a particular station is not broadcasting properly or a station is conducting tests, the RDS reception function may not work properly. • When you receive an RDS station whose signal is too weak, information like the station name may not be displayed, even if “RDS” is lit. 29 EN CASSETTE OPERATION 44 1 2,5 3 6 P.CALL 4 1 . . 2,5 6 7 P.CALL 4 1 . . 1 3 7 STOP REVERSE MODE TAPE A or TAPE B playback 1 Press the ON/STANDBY button to turn the power on. 2 Press the TAPE (A/B) button. 3 Open the cassette door by pushing the area marked “PUSH OPEN”. 4 Load the cassette into the TAPE A or TAPE B cassette compartment. 5 With cassette in both decks, press the TAPE (A/ B) button to switch operation from one deck to the other. 6 Press the 3 button to start playback. • When playback is performed using the remote control, press the 3 button. To stop playback : Press the 7 STOP button. Fast forward/rewind : 1 Press the 7 STOP button, then press the TAPE (A/B) button to select TAPE A or TAPE B. 2 To advance the tape, press the P. CALL . . button. To rewind it, press the P. CALL 4 1 button. Caution : • To remove the cassette tape, press the 7 STOP button, and then open the cassette compartment. • Before changing from one tape operation to another, press the 7 STOP button. • If a power failure occurs during tape operation, the tape head will remain engaged with the tape and the cassette door will not open. In this case, wait until power is restored. Selection of reverse mode (TAPE B only) : Press the REVERSE MODE button repeatedly to select the following setting : • “ ” ....Playback stops after having played both sides of tape in a deck. • “ “.....Endless playback of both sides of tape. • “ “.....Playback stops after having played one side of tape. 30 EN RECORDING (TAPE B only) • When recording important selections, be sure to make a preliminary test to ensure that the desired material is being properly recorded. • The volume and sound quality can be adjusted with no effect on the recorded signals (Variable Sound Monitor). • Metal and CrO2 tapes should not be used for recording or dubbing. Recording from the built-in radio 1Tune in to the desired station. (see pages 19 21) 2 Load a cassette into the TAPE B cassette compartment. 3 Press the REC PAUSE button • “REC.” and “¶ 2 3” will flash. 4 Press the 2 or 3 button. • “REC.” will disappear and “¶ 2 or ¶ 3” will light up on the display. Note : • If a whistling noise is heard whilst recording from an AM station, move the AM loop antenna to a position where noise is no longer heard f...

Descargar ahora

Introduzca dos números de la imagen: