Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
If you are connecting any additional gear that is not included in the CLUB-6800, refer to the appropriate manuals for detailed instructions. Gathering Package Contents The first step to putting together your new CLUB-6800 system is unpacking all of the necessary equipment. Remember to keep your manuals nearby when setting up, as you may need to reference them. The products listed below are included in the CLUB-6800 system: CDG-9000 PRO SS-88 Speaker Stands • [1] Instruction Manual • [2] SS-88 speaker stands KJM-8000 PRO Digital Key Control Karaoke Mixing Board CLUB-8 Road Case • [1] Instruction Manual • [1] CLUB-8 road case • [1] Rolling cart VP-600 PRO 600W Professional Power Amplifier • [2] MK-38 PRO microphones • [1] Instruction Manual • [1] Gooseneck DJ light • Rack-mounting screws VX-15 Vocal Speakers • [2] VX-15 speakers Mounting components into the CLUB-8 Follow these basic guidelines when mounting: • Always screw in the mounting screws using an “X” formation. • If possible, to keep the products cooler, leave some space in between the components in the rack. CDG-9000 PRO CONTROLLER KJM-8000 PRO MIXER CDG-9000 PRO PLAYER VP-600 PRO AMPLIFIER 1243On the web at or call toll free 1-800-678-5348 Below is one way to configure your CLUB-6800: Setting up the speakers and speaker stands 1. Setup each SS-88 speaker stand by extending the support VX-15 Speaker legs to a position that is stable and tighten the tension mechanism firmly. 2. Place a VX-15 speaker on top of the SS-88 so that the shaft of the SS-88 fits flush into the mounting cavity on the bottom of the VX-15. NOTE: Each end of the SS-88 pole has a particular diameter fitted for common speakers’ mounting cavities. If the SS-88 shaft does NOT fit flush into the mounting cavity on the VX-15, loosen the SS-88 pole and reverse it in the stand and then SS-88 Stand remount the speaker. 3. Repeat the above steps for each speaker and stand. Connecting Power Be sure that each product has a power cord firmly attached. It is recommended that you use a power strip/surge protector when connecting your CLUB-6800 to a power outlet. Connecting the components Once you have mounted all of the components into the CLUB-8, it is time to connect them. Follow these directions on connecting the components. NOTE: If you are also connecting components that are not part of the CLUB-6800 system, please refer to the manual of that product for setup instructions. MAKE SURE THAT ALL PRODUCTS’ POWER IS TURNED OFF BEFORE CONNECTING ANYTHING 1 CDG-9000 PRO remote unit to the player unit Connect the Control Interface Connector from “CONNECT TO MAIN UNIT” jack on the rear panel of the remote unit to the “CONNECT TO REMOTE CONTROLLER” jack on the rear panel of the player unit. CDG-9000 PRO Controller CDG-9000 PRO Player CLUB-6800 CDG-9000 PRO player unit to KJM-8000 PRO You have the option of either connecting each deck of the CDG-9000 PRO separately (Fig. 1) or together through a single SWITCHED output (Fig. 2). Separately through individual deck outputs (Fig.1) Using RCA cables: 1. For each deck, connect the L/R (red & white) audio outputs and Video (yellow) output on the CDG-9000 PRO to the CDG(1) and DVD(3) inputs on the rear panel of the KJM-8000 PRO CDG(1) DVD(2) LD(3) CDG(1) DVD(2) LD(3) CDG-9000 PRO Player 2 KJM-8000 PRO Mixer Together through SWITCHED output (Fig. 2) Using RCA cables: 1. Connect the L/R SWITCHED audio and SWITCHED video outputs on the CDG-9000 PRO player to the CDG(1) audio input on the KJM-8000 PRO CDG(1) DVD(2) LD(3) CDG-9000 PRO Player KJM-8000 PRO Mixer KJM-8000 PRO to VP-600 PRO You can do this using either XLR(f) to XLR(m) cables or XLR(f) to .”(m) cables. Below are instructions for each. 3 CDG(1) DVD(2) LD(3) STEREO MONO BRIDGE INPUTS CH. B CH. A BALANCED BRIDGED OUTPUTS MODEL VP-600 PRO STEREO 300W PER CHANNEL INTO 4 OHM 600W MONO BRIDGED INTO 8 OHM CH. B CH. A MONO Using two XLR(f) to .”(m) (Fig. 2) 1. Connect the XLR(f) end to the LEFT MASTER AUDIO XLR output on the KJM-8000 PRO and the .”(m) end to the CH. B .” audio input on the VP-600 PRO. 2. Now do the same thing except now go from the RIGHT MASTER AUDIO XLR output on the KJM-8000 PRO and the CH. A .” audio input on the VP-600 PRO. CDG(1) DVD(2) LD(3) STEREO MONO BRIDGE INPUTS CH. B CH. A BALANCED BRIDGED OUTPUTS MODEL VP-600 PRO STEREO 300W PER CHANNEL INTO 4 OHM 600W MONO BRIDGED INTO 8 OHM CH. B CH. A MONO VP-600 PRO Amplifier KJM-8000 PRO Mixer Using two XLR(f) to XLR(m) (Fig.1) 1. Connect the XLR(f) end to the LEFT MASTER AUDIO XLR output on the KJM-8000 PRO and the XLR (m) end to the left XLR audio input on the VP-600 PRO. 2. Now do the same thing except now go from the RIGHT MASTER AUDIO XLR output on the KJM-8000 PRO and the right XLR audio input on the VP-600 PRO VP-600 PRO to VX-15 speakers Using two 9’ MDP (Banana Plug) to .” speaker cables 1. Connect the MDP end to CH.B on the rear panel of the VP-600 PRO and 2. Connect the .” end to one of the two VX-15’s. 3. Repeat t...