Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Crossfader Reverse -The crossfader reverse changes the direction of the fade on the crossfader (23). FRONT PANEL FRONT PANEL 25. Crossfader Curve -Controls the taper (fade) shape of the crossfader (23). The crossfader curve control continually adjusts the curve from a sharp cut to a long fade. 26. Headphone Outputs -1/4” and 1/8” connector jacks for headphones. BACK PANEL BACK PANEL Power -Power switch to turn the mixer “ON” or “OFF”. AC IN: This is the input connection for the included power supply. Master -Connects to an amplifier, EQ, crossover, or other outboard signal processing. Connect balance connections to the TRS 1/4” connectors. Connect un-balanced connections to the RCA connectors. Line -Line inputs are used to connect line level sources such as CD players, Mini Discs, DATs, samplers, etc. Ground -Connects to turntable ground cable to eliminate electrical hum. Ground cables are usually supplied with turntables. Phono -Connects to left and right RCA cables from turntable. Mic -1/4” TRS connector for use with microphones. REMOVING FACEPLATE REMOVING FACEPLATE 1. Unplug the power supply from the back of the mixer. Verify that the mixer is powered off. 2. Remove the 4 screws on the faceplate. Place the 4 screws somewhere safe where they will not be lost. 3. Remove the 3 fader knobs from the line faders and crossfader. 4. The faceplate can now be removed from the top of the mixer. (BACKPANEL VIEW) 2222333 CLEANING FADERS 1. Make sure the mixer is powered off. Remove the faceplate of the mixer by following the directions above. 2. Remove the fader from the mixer by unscrewing the two outer screws on the fader plate. Do not remove the two inside screws on the fader plate; this will remove the fader from the fader plate. 3. Once fader has been removed from mixer, spray a small amount of contact cleaner into the fader and move the fader back and forth to disperse the cleaner. ROTATING THE TRANSFORM SWITCHES ROTATING THE TRANSFORM SWITCHES The input selector (transform) switches on the Stanton SA.3 mixer can be rotated to 8 different positions. Follow the steps below to rotate the transform switch to the position you like. 1. Make sure the mixer is powered off. Remove the faceplate of the mixer. 2. Remove the two outer screws from the transform switch as indicated in diagram. Do not remove the two inner screws. Removing the two inner screws will detach the switch from the plate. 3. Rotate the switch to the position you like. Replace the two outer screws to secure the switch in place. Replacing the transform switch 1. Follow steps 1 and 2 above. Remove switch from mixer and detach connector from switch. 2. Attach connector for transform switch to replacement switch and replace two outer screws to secure the switch in place. REPLACING THE CROSSFADER The SA.3 is compatible with the CFSA.3, Focus Faders V1/V2 and with Penny and Giles crossfaders. The SA.3 has two different circuits which need to be switched when changing between the faders. To switch the crossfader circuit, follow the instructions below: 1. Follow steps 1 & 2 from the fader cleaning instructions. 2. Remove the fader assembly and disconnect the cable coming from the mixer. 3. The crossfader select switch is located inside the mixer, on the left side of the fader slot. In order to use the CFSA.3, FF1 and Penny & Giles faders, make sure the switch is pressed DOWN. To use the CFF2, make sure the switch is in the UP position. TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Line inputs: 2 (RCA) x 2 channels, -10 dBV /10 kOhm Phono inputs: 2 (RCA) x 2 channels, -50 dBV / 47 kOhm Master output: 2 (TRS Balanced/RCA unbalanced), +4 dBu balanced / -10 dBV unbalanced Headphone output: 1 (1/4 inch), 1 (1/8 inch), greater than 32 Ohm load Frequency Response: 20 Hz - 20 kHz, +/- 1.5 dB Tone Control : Hi +9/-18 dB Mid +9/-25 dB Low +9/-25 dB S/N Ratio: Better than 94 dB (ref: max input level) Noise: -80 dBV (Line input to any output) T.H.D Less than 0.04% (1 kHz) Dimension(LxWxD): 12.4" x 9.25" x 4.33"in; (315 x 235 x 110mm) Weight: 6.6 lbs 3 kgs REPLACEMENT PARTS The following user replaceable parts are available from your local Stanton dealer. CFSA3 Crossfader LFSA3 Linefader CF-PG110 Penny & Giles crossfader CF-F1 Focus Fader V1 CF-F2 Focus Fader V2 PLSA3 Phono / Line switch 3PLSA3 Phono / Line switch (w/Flash) PPSA3 PROTEKT™ panel PS-18US US Power Supply (110v) PS-18EU European Power Supply (220v) PS-18UK UK only Power Supply (240v) WARRANTY WARRANTY Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement Warranty Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) following the date of original purchase. Exceptions to this ...