Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Each output jack is designed for a four ohm load. These jacks are parallel internally, resulting in the rated two ohm load. NEVER OPERATE THE AMPLIFIER WITH LOADS LESS THAN TWO OHMS. Because this amp is capable of delivering 20 amps of peak current, it is necessary to use very large wire (16 gauge or larger) if extremely long speaker leads are necessary. PEAVEY ELECTRONICS TECHNICAL SPECIFICATIONS MODEL: F-800B POWER AMPLIFIER SECTION: A. Output Power @ 1 KHZ @ 117 VAC Line: 1. Rated Power: 400 W RMS @ Rated Load: 2 OHMS 2. Power vs. Distortion: LOAD IMPEDANCE 8 4 2 1 OHMS OUTPUT @ 1% THD 150 260 410 160 W OUTPUT @5% THD 170 290 450 220 W B. Peak Output @ Rated Load: 20 AMPS & 40 VOLTS, 800 WATTS C. Music Power Output @ Rated Load: 500 WATTS RMS @ 1% THD D. Frequency Response: 3 DB Down @ 40 HZ & 15 KHZ E. Sensitivity @ Rated Power & Load: 800 mV F. Input Impedance: 10 K OHMS PRE-AMPLIFIER SECTION: A. Input Characteristics: (Tone Controls Flat, Volume @ 12:00) 1. Sensitivity: 30 mV @ 1 KHZ 2. Input Impedance: 330 K OHMS 3. Noise: 60 DB (Open Ckt), 68 DB (50 K OHMS) 74 DB (Short Ckt)* B. Distortion @ 1 KHZ @ Rated Output: Less Than 0.1% THD** C. Frequency Response: 3 DB Down @ 40 HZ & 30 KHZ D. Tone Controls: + 20 DB @ 50 HZ & 5 KHZ E. Middle Control: 20 DB Cut F. 6 Channel Equalizer: + 12 DB each Channel G. Distortion Control: Variable Harmonic Distortion with Foot-switch Cut-off H. Slope Control: Switch selected Low Frequency Roll-Off Signal-to-noise ratio in DB below rated output ** Measured with Distortion control cut-off (Full CCW) PEAVEY ELECTRONICS TECHNICAL SPECIFICATIONS MODEL: F-800G I. POWER AMPLIFIER SECTION: A. Output Power @ 1 KHZ @ 117 VAC Line: 800 MODULE 1. Rated Power: 400 W RMS @ Rated Load: 2 OHMS 2. Power vs. Distortion: LOAD IMPEDANCE 8 4 2 1 OHMS OUTPUT @ 1% THD 150 260 410 160 w OUTPUT @ 5% THD 170 290 450 220 w B. Peak Output @ Rated Load: 20 AMPS & 40 VOLTS, 800 WATTS C. Music Power Output @ Rated Load: 500 WATTS RMS @ 1% THD D. Frequency Response: 3DB Down @ 40 HZ & 15 KHZ E. Sensitivity @ Rated Power & Load: 800 mV F. Input Impedance: 10 K OHMS II. PRE-AMPLIFIER SECTION: A. Input Characteristics: (Tone Controls Flat, Volume @ 12:00) 1. Sensitivity: 30mV@1KHZ 2. Input Impedance: 330 K OHMS 3. Noise: 60 DB (Open Ckt), 68DB (50 K OHMS) 74 DB (Short Ckt)* B. Distortion @ 1 KHZ @ Rated Output: Less Than 0.1% THD ** C. Frequency Response: 3DB Down @ 40 HZ & 30 KHZ D. Tone Controls: + 20 DB @ 50 HZ & 5 KHZ E. Middle Control: 20 DB Cut F. 6 Channel Equalizer: + 12 DB each Chan. G. Reverb Control: Continuously Variable with Foot-switch Cut-Off H. Distortion Control: Variable Harmonic Distortion with Foot-switch Cut-Off I. Fuzz Control: Adjustable Attack & Harmonics with Foot-switch Cut-off. J. Tremolo Controls: Variable Depth & Rate with Foot-switch Cut-Off K. Slope Control: Switch selected Low Frequency Roll-Off *Signal-to-noise ratio in DB below rated output #* Measured with Distortion, Reverb, Fuzz, & Tremolo controls cut-off (Full CCW) PEAVEY ELECTRONICS CORP. 611 - 10TH AVENUE / P. 0. BOX 2898 / MERIDIAN. MISS 39301 / PHONE 1601) 483 5365 Specifications published in this manual are subject to change without notice Printed in U.S.A....
Otros modelos de este manual:Instrumentos Musicales - F800B (680.04 kb)
Instrumentos Musicales - F800G (680.04 kb)
Instrumentos Musicales - F800B (680.04 kb)