Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
15. PRESENCE: Increase the level of upper harmonics with this control. The presence control allows a boost of up to 5dB at 10kHz. 16. STANDBY: This switch activates the amplifier, and should always be turned on last. The switch lights up when the high voltage power is passing through to the tubes. NOTE: When you first power up this amplifier, leave the Standby switch OFF for at least 20 seconds. This gives the power tubes a chance to prepare themselves for action. 17. POWER: This switch applies AC voltage to the amplifier, and should always be turned on first. The switch lights up when the AC power is on. ®BV-60/6212 All-Tube Professional Series Guitar Amplifiers 5 MODEL SERIAL # BV-60 100V - 125V T2.5A SLO-BLO 230V - 250V T1.5A SLO-BLO AC LINE IN AVIS:RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, SO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CH. SEL REVERB SEND RETURN ONE 8 OHM ENCLOSURE ONE 4 OHM ENCLOSURE TW0 16 OHM ENCLOSURES TWO 8 OHM ENCLOSURES EFFECTS LOOP BAL. OUT SPEAKER CONNECTIONS 60 WATTS RMS M A D E I N T H E BY SLM ELECTRONICS – 1 4 0 0 F E R G U S O N A V E . – S T . L O U I S , M O . 6 3 1 3 3 U . S . P A T E N T # 5 , 0 1 2 , 1 9 9 U . S . A . 115VAC–60Hz 360 WATTS MAX. CAUTION: TO REDUCE THE RISK OF FIRE, REPLACE FUSE WITH SAME TYPE AND RATING. ATTENTION: UTILISER UN FUSIBLE DE RECHARGE DE MEME TYPE. 18 19 20 22 FOOT SWITCH 21 23 24 25 The Rear Panel: 18. FUSE: This fuse protects the amplifier against damages caused by overload conditions in the unit. If the fuse blows, replace it only with the same size and type as indicated on the rear panel. If the fuse blows continually, the line voltage may be incorrect, or the amp may need servicing. 19. AC LINE IN: Firmly plug the female end of the supplied power cord into this socket, pushing it in until it is fully seated. Plug the male end of the cord into a properly grounded AC outlet of the correct voltage. DO NOT DEFEAT THE GROUND PIN OF THE AC PLUG! Use only the supplied power cord. If the amplifier is to be used outside of the United States, see your authorized Crate dealer for information about alternate line cords and power converters if needed. 20. CHANNEL SELECT FOOTSWITCH JACK: Connect a stereo 1/4”plug (tip/ring/sleeve) here from either a two or three button footswitch (such as the Crate CFP-2 or CFP-3) for control of channel switching. The tip of the jack is for the channel switching; the ring is for boost control. When a footswitch is connected here, the front panel channel select and boost switches are disabled. 21. REVERB FOOTSWITCH JACK: Connect a mono 1/4”plug (tip/sleeve) here from either a one or three button footswitch for reverb on/off control. 22. EFFECTS LOOP SEND: Connection to an external effects device is made via this jack. Connect a shielded instrument patch cord from the send jack to the input jack of the effect. The send jack also doubles as a "preamp out" jack, to feed a post-eq signal to a mixing board, recording console or external amplifier. 23. EFFECTS LOOP RETURN: Connection from an external effects device is made via this jack. Connect a shielded instrument patch cord from the output jack of the effect to the return jack. The return jack also doubles as a "power amp in" jack, to feed a line-level signal directly into the BV-60/62's internal power amp. This is useful when "slaving" two amplifiers together. 24. BALANCED OUT JACK: This XLR connector supplies a balanced output signal from the power amp for patching into a mixing board, recording console or external amplifier. The signal is electronically compensated to simulate the sound of a “miked” cabinet. 25. SPEAKER JACKS: Use these unbalanced 1/4" jacks to connect the amplifier to your speaker cabinet(s) as shown below. NOTE: You may use any configuration of impedances shown at the speaker output jacks. Impedance matching is automatic: simply connect the cabinet(s) to the jack(s) labeled with the corresponding impedance( s). # of CABS JACK JACK & IMPED(S) LOCATION(S)* LABEL(S) 1 @ 4 ohms #3 4 OHM 1 @ 8 ohms #1 8 OHM 2 @ 8 ohms #3,4 2-8 OHM 2 @ 16 ohms #1,2 2-16 OHM * Jacks numbered here for purpose of illustration only: To avoid damaging the amplifier and the speaker cabinets, don’t use two 4 ohm cabinets, or one 8 ohm and one 4 ohm cabinet at the same time. Do not connect a single 16 ohm cabinet to the speaker output jacks. A SPEAKER LOAD MUST BE CONNECTED TO THE AMPLIFIER TO AVOID DAMAGING THE UNIT. ONE 8 OHM ENCLOSURE ONE 4 OHM ENCLOSURE TW0 16 OHM ENCLOSURES TWO 8 OHM ENCLOSURES SPEAKER CONNECTIONS 1 2 3 4 ®BV-60/6212 All-Tube Professional Series Guitar Amplifiers Channel 1 Channel 2 Reverb CHANNEL VOLUME LOW MID HIGH GAIN LOW MID HIGH MASTER REVERB PRESENCE BRIGHT BOOST IN OUT Channel 1 Channel 2 Reverb CHANNEL VOLUME LOW MID HIGH GAIN LOW MID HIGH MASTER REVERB PRESENCE BRIGHT BOOST IN OUT Channel 1 Channel 2 Reverb CHANNEL VOLUME LOW MID HIGH GAIN LOW MI...
Otros modelos de este manual:Instrumentos Musicales - BLUE VOODOO BV-60 (1.19 mb)