Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Rugged construction, reliable American craftsmanship and two powerful channels of pure tube power are some of the trademarks of these new and impressive pieces of musician's equipment. Both amplifiers feature two distinctly different 12AX7 tube-driven channels: one with classic tube rhythm sounds and one offering you some of the finest lead and overdrive sounds of any stock amplifier. Each channel features an all-tube preamp section with separate reverb level controls and three bands of equalization for total tone control. The master Presence control lets you custom tailor the sound of your guitar to suit your particular needs. The Line Out signal is tapped directly from the speaker outputs, then attenuated and frequency-compensated to replicate the sound of a miked speaker cabinet. Two pairs of speaker output jacks provide easy and automatic impedance matching with a wide variety of cabinet configurations. The BV-60 and BV-6212 boast a solid 60 watts of musical output power. Features: Here's a quick overview of the BV-60/6212's features and controls. Additional information can be found on the pages indicated. • Patented Channel Switching Circuitry: Achieves maximum use of each preamp tube – so unique it’s patented! • Boost Control: Like adding a third channel to your amp. This push-button switch gives a big boost to the midrange frequencies and the overall gain of the overdrive channel (footswitchable) (page 4). •Adjustable Presence Control: Fully adjustable upper harmonics level for changing the “presence” of both channels (page 4). •Auto-Biasing Circuitry: Want to change your sound? Change your tubes! Internal circuitry allows the use of either 6L6 or EL34 power tubes with no bias adjusting (page 7). •DC Filament Supply: The first preamp tube has a DC filament supply for reduced hum. •Effects Loop: For noiseless patching of external effects, or use as a preamp out/power amp in connection (page 5). •Balanced Out Jack: Taken directly from the speaker output signal, this electronically balanced and frequency compensated output lets you patch into house sound boards, recording consoles, etc., with ultimate sonic fidelity (page 5). • Footswitch Jacks: Two separate jacks – one for channel selection and boost control and one for reverb on/off control – allow use of a two or three-button footswitch for total control (page 5). • Speaker Jacks: Impedance-matched speaker connectors for up to four different cabinet configurations (page 5). • High Cosmetic Appeal and Stage Presence: The unique cosmetics of the BV-60/6212 serve as a tribute to your good taste in musical equipment. • Musician Made in the U.S.A. 4 Channel 1 Channel 2 Reverb CHANNEL INPUT VOLUME LOW MID HIGH GAIN LOW MID HIGH MASTER REVERB PRESENCE STANDBY POWER 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 BRIGHT 9 BOOST The Front Panel: 1. INPUT: Connect your guitar or wireless receiver into this standard 1/4" jack using a shielded instrument cable. Channel 1: 2. VOLUME: Set the output volume level of channel 1 with this control. 3. LOW: Adjust the bottom end response with this control. The low control covers a range of 16dB at 100Hz. 4. MID: Adjust the midrange response with this control. The mid control covers a range of 23dB at 300Hz. 5. BRIGHT: Add a biting edge to your sound by pressing this push-button switch in. The bright switch adds 5dB at 5kHz. 6. HIGH: Adjust the high end response with this control. The high control covers a range of 25dB at 10kHz. 7. CHANNEL: Switch between channels with this push-button switch. The adjacent amber LED glows when channel 1 is selected (switch "out"), the red LED glows when channel 2 is selected (switch "in"). When a footswitch is used for channel switching, this switch is disabled. Channel 2: 8. GAIN: Adjust the overdrive (distortion) level with this control. With the control towards “0” (to the left) the signal is relatively clean. As you bring the control towards “5” (center position) the distortion increases, along with the overall output level. Keep turning the control towards”10” and you’ll increase the distortion even more. 9. BOOST: Add a third channel (sort-of) by pressing this push-button switch in. The boost switch adds 13dB at 1kHz. 10. LOW: Adjust the bottom end response with this control. The low control covers a range of 8dB at 100Hz. 11. MID: Adjust the midrange response with this control. The mid control covers a range of 7dB at 700Hz. 12. HIGH: Adjust the high end response with this control. The high control covers a range of 10dB at 10kHz. 13. MASTER: Set the output signal level of channel 2 with this control. At the "0" position (full left) very little or no signal will be heard; as you bring the control up (towards center) the output level of channel 2 increases. Use this control along with your guitar's volume and the Gain control (#8) to produce a wide variety of sounds. 14. REVERB: Adjust the amount of reverberation with this control: at the "0" position the signal is "dry" (no reverb). As y...
Otros modelos de este manual:Instrumentos Musicales - BLUE VOODOO BV-6212 (1.19 mb)