Votos - 3, Puntuación media: 2.7 ( )

Fabricar: Roland Tamaño del archivo: 9.13 mb Nombre del archivo: Idioma del manual:

NOTE Bottom Panel 23 Fornormal use,donotconnectanythingtothisconnector. GettingReady Connecting the AC Adaptor Connectthe included ACadaptor tothe DC IN connector on the rear panel of the VP-7. Power Cord Indicator NOTE • PlacetheACadaptorsothesidewiththe indicator(see illustration)facesupwardsandthesidewithtextualinformation faces downwards. The indicatorwilllightwhenyouplugtheACadaptorintoanACoutlet. • Securely inserttheACadaptorplugallthewayintotheconnector. • Use only the suppliedACadaptor. Attaching the VP-7 to a stand Byusing the separately sold PDS-10 and BKT-S, you can attach the VP-7 toastand as shown in the illustration. * Use only the screws provided with the BKT-S Other screws may damage the unit * When using the PDS-10, extend the legs to their maximum spread Do not allow the overall height including the VP-7 to exceed 1 meter 928 * When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to the buttons and controls Also, you should try to orient the unit so no buttons or controls get damaged 929 * When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over Connecting a Keyboard Connecting a Keyboard MIDI Cable MIDI IN Keyboard MIDI OUT If you run a cable from the output of your keyboard (which you’ve con- nected to the MIDI IN connector) to the LINE IN jack, you’ll be able to carryout performances that use Human Voice or Vocal Designer in combination with whatyou playon the keyboard. * The VP-7’s [Volume] knob does not affect the LINE INPUT Use the volume control of the connected keyboard to adjust the volume MEMO Ifakeyboardisnotconnected,thepitchfromthemicrophoneinputwillbedetected,andthepitchofthe soundsproduced will be based on this detected pitch. Changing the MIDI receive mode Atthe factorysettings,the VP-7 is set toMIDI channel 1. Ifyou wantto receive multiple channels, you can change the MIDI reception mode so thatall channels 1–16 will be received (OMNI). Ifyou set the VP-7’s MIDI reception mode so thatonly channel 1is received, you must also set the transmitting MIDI device tochannel 1. To check the current MIDI reception mode The button illumination when the VP-7 is powered up will indicatethe currentMIDI reception mode. Reception mode Button illumination Ch1 When you turn on the power, the selected sound button will light. OMNI When you turn on the power, all of the sound buttons will simultaneously blink twice,and then the selected sound button will light. To change the MIDI reception mode While holding down the [Bypass] button, turnon the power. Each time you do this, the setting will alternate between Ch1/OMNI. Reception mode Explanation Ch1 Only the data of channel 1will be received OMNI All channels will be received When you change the MIDI reception mode, the setting is automatically stored in the unit; it will still be in effect the nexttime power is turned on. * Even if you set the MIDI reception mode to OMNI, you still won’t be able to use the unit as a multitimbral sound generator Connecting Headphones or Speakers Connecting Headphones or Speakers NOTE Topreventmalfunctionand/ordamageto speakersorotherdevices,alwaysturndownthevolume,andturnoffthepower on all devices beforemaking anyconnections. Connecting monitor speakers or a stereo system Use cablestoconnecttheVP-7’srear panel OUTPUT jackstoyour monitor speaker or stereo set. * In order to take full advantage of the VP- 7’s capabilities, we recommend that you use it in stereo . * To use it in mono, connect to the OUTPUT L/MONO jack . Monitor speakers (with built-in amp) INPUT Audio Cable OUTPUT Using headphones Connectcommerciallyavailable head phonestothe Headphone jack. * Sound will be output from the OUTPUT jacks even if headphones are connected Headphones Headphone Jack (Stereo miniature phone type) Connecting a Microphone Connecting a Microphone . TheVP-7 modelsvocal soundsbyusingyourvoicethatisinputviathemicrophone. 922 * This instrument is equipped with balanced (XLR/TRS) type jacks Wiring diagrams for these jacks are shown below Make connections after first checking the wiring diagrams of other equipment you intend to connect 1: GND2: HOT3: COLDTIP:HOTRING:COLDSLEEVE:GND983 * Howling could be produced depending on the location of microphones relative to speakers This can be remedied by: 1. Changing the orientation of the microphone(s). 2. Relocating microphone(s) atagreater distance from speakers. 3. Lowering volume levels. * Note that if you don’t have a MIDI keyboard connected, the Human Voice sound could continue sounding without end if the input from the microphone is at too high a level Should you encounter this problem, turn the [Mic] knob counterclockwise to lower the level of the input * For information on how to wear the microphone, refer to the owner’s manual that came with the supplied microphone If using a phantom-powered microphone The VP-7’sMIC IN jack can provi...

Descargar ahora

Introduzca dos números de la imagen: