Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Transmit data ■ Channel Voice Messages • Note off Status 8nH 2nd byte kkH 3rd byte 40H n=MIDI channel number: OH - FH (ch.l - ch.16) kk=note number: 00H - 7FH (0 -127) • Note on Status 2nd byte 9nH kkH n=MIDI channel number: kk=note number: w=note on velocity: 3rd byte wH OH - FH (ch.l - ch.16) ООН - 7FH (0 -127) 01H - 7FH (1 -127) Note number's range can be changed with Key Transpose: up a maximum 5, or down a minimum of 6 semitones. The table below shows the degrees of transposition. transpose transmitted note number -6 15-102 -5 16-103 -4 17-104 -3 18-105 -2 19-106 -1 20-107 0 21-108 +1 22-109 +2 23-110 +3 24-111 +4 25-112 +5 26-113 • Control Change O Data Entry (Controller number 6,38) Status 2nd byte 3rd byte BnH 06H mmH BnH 26H 11H • Data transmission HP-330/530/245 can transmit and receive the various parameters using System Exclusive The exclusive message of HP-330/530/245 data has a model ID of 1AH, and device ID is defined by MIDI UNIT NUMBER. UNIT NUMBER is always the same as the current basic channel. n=MIDI channel number: OH - FH (ch.l - ch.16) mm,11= the value of the parameter specified by RPN O Expression (Controller number 11) Status 2nd byte 3rd byte BnH OBH wH O Data set 1 DT1 This is the message that actually performs data transmission, and is used when you wish to transmit the data. Status FOH Byte FOH 41H dev 1AH 12H aaH bbH ccH ddH sum F7H Data byte 41H, dev, IAH, 12H, aaH, bbH, ccH,... ddH, sum Status F7H Explanation Exclusive status ID number (Roland) Device ID (dev: UNIT#-1) Model ID (HP-330/530/245) Command ID (DTI) Address MSB: upper byte of the starting address of the transmitted data Address LSB: lower byte of the starting address of the transmitted data Data: the actual data to be transmitted. Multiple bytes of data are transmitted starting from the address. Data Checksum EOX (End Of Exclusive) n=MIDI channel number: OH - FH (ch.l - ch.16) w=Expression: 00H - 7FH (0 -127) * Continuous value is transmitted. * Transmitted when pedal function 2 or 4 is selected. O Hold 1 (Controller number 64) Status 2nd byte 3rd byte BnH 40H wH n=MIDI channel number: OH - FH (ch.l - ch.16) w=Control value: 00H - 7FH (0 -127) * Continuous value is transmitted. O Sostenuto (Controller number 66) Status 2nd byte 3rd byte BnH 42H wH n=MIDI channel number: vv=Control value: OH - FH (ch.l - ch.16) 00H, 7FH (0,127) 0=OFF 127=ON Data larger than 128 bytes must be divided into packets of 128 bytes or less. If "Data Set 1" is transmitted successively, there must be an interval of at least 20 ms between packets. Regarding the address please refer to section 3 (Parameter Address Map). Regarding the checksum please refer to section 4 (Supplementary material). ON or OFF is transmitted. 3 MIDI IMPLEMENTATION O Soft (Controller number 67) Status 2nd bvte 3rd byte BnH 43H wH n=MIDI channel number: OH - FH (ch.l - ch.16) w=Control value: ООН - 7FH (0 -127) * Continuous value is transmitted. О Effect 1 (Reverb Send Level) (Controller number 91) Status 2nd byte 3rd byte BnH 5BH wH n=MIDI channel number: OH - FH (ch.l - ch.16) w=Control value: ООН, 7FH (0,127) 0=OFF 127=ON * Transmitted when MIDI transmit mode 2 is selected. О Effect 3 (Chorus Send Level) (Controller number 93) Status 2nd byte 3rd byte BnH SDH wH n=MIDI channel number: OH - FH (ch.l - ch.16) vv=Control value: ООН, 7FH (0,127) 0=OFF 127=ON * Transmitted when MIDI transmit mode 2 is selected. О RPN MSB/LSB (Controller number 100,101) Status 2nd byte 3rd byte BnH 65H mmH BnH 64H ИН n=MIDI channel number: OH - FH (ch.l - ch.16) mm=upper byte of parameter number specified by RPN ll=lower byte of parameter number specified by RPN * Transmitted when MIDI transmit mode 2 is selected. *** RPN ** HP-330/530/245 can transmit Master fine tuning (RPN #1) and RPN null. After sending the master fine tune, immediately the RPN Null shall be sent. RPN Data entry MSB LSB MSB LSB Explanation_ ООН 01H mmH 11H Master Fine Tuning mm,11:00 00H - 40 ООН - 7F 7FH (-100 - 0 - +100 cents) 7FH 7FH----RPN null * Program Change Status 2nd byte CnH ppH n=MIDI channel number: OH - FH (ch.l - ch.16) pp=Program number: 00H - 7FH (prog.l - prog.128) * When this piano is set to MIDI transmit mode 2, pressing a Tone button will select a tone as usual. At this time, the Program Change message assigned to that button is sent. ■ System exclusive messages HP-330/530/245 can transmit and receive the various parameters using System Exclusive messages. The exclusive message of HP-330/530/245 data has a model ID of 1AH, and device ID is defined by MIDI UNIT NUMBER. UNIT NUMBER is always the same as the current basic channel. The System Exclusive Messages transmitted by the HP-330/530/245 are; Data Set (DTI), and Universal Non-realtime System Exclusive messages (Identity Reply). * Universal Non-realtime System Exclusive Messages 0 Identity Reply Status Data byte Status F0H 7EH,...