Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
Also, to record from the middle of the music, do it in the Manual recording mode. * The head of the sound may be missed out if it is extremely quick attack sound. * To rerecord the sound, set the Sampler Mode Switch 0 to the IS position then return to E9. RANGE/MODE RANGE/MODE RANGE/MODE (5) For overdubbing, rotate the Overdub Level Knob 0 clockwise, then repeat the step (3), (@) and (§). FEEDBACK OVERDUB (Playback) © Set the Sampler Mode Switch 0 to the 0 or 0 position, then play the keyboard. RANGE/MODE RANGE/MODE The sampled sound will be played back according to the key played. © To make the keyboard's output level in the 0 mode equal to that in the S mode, try changing the Sampler Mode Switch 0 alternately to the 0 and 0 positions and playing the keyboard. The volume in the H mode does not change, but that in IS mode is adjustable. When using the keyboard with dynamics, play the keyboard rather hard for adjusting the level. In the 0 mode, the sampled sound will be all played back no matter how short you touch the keyboard. * When the RSD-10 is set to the position Q|, 0 or H, it detects the pitch of the sound's head for about 50ms. Therefore, the staccato (shorter than 50ms) or unstable sound is not suitable for pitch controlling; wrong pitch is recorded or played back. Playback with dynamics is not possible. 18 In the 0 mode, the sampled sound can be played back only while the key is played. To obtain the effect such as dynamics, pitch bender, vibrato, portamento etc, set the RSD-10 to the 19 mode. (These effect does not work in any other mode.) * Changing the pitch will slightly alter the timbre simultaneously. (9) Using the Playback Trim Knob, adjust the length of the playback sound. At 100%, the recorded sound will entirely played back. As you rotate the knob counterclockwise, the tail of the sound will be cut. ® If you wish to play with the original sound of the synthesizer, turn the Effect Switch 0 off. 50 t I / The Effect Indicator© goes out, and the keyboard signal will be bypassed. 2 Delay Mode ■ CONNECTIONS To AC Adaptor Jack и BOSS PSA-120, 220, 240 (Optional) я AC Adaptor To Other BOSS Micro Studio Series Foot Switch (FS-1: Optional) (DP-2) , -KMn O© I o§ M OUT 9V DC ШШВ-4 SHS-© EFFECT PAD REMOTE TRIG KEYBOARD TAPE MPUT НАОС M M All the BOSS Micro Studio Series show the current draw here. Keyboard * The microphone can be directly connected to the Input Jack only when it has sufficient output. MIC IN , О Preamplifier/Parametric Equalizer 1 . о B0 D oooo Tape Recorder Keyboard CD Player Electric Guitar ooftltloo @© 4........... r Guitar Amplifier Mixer (BOSS BX Series etc.) Tape Recorder Г°c 1 ЕЗЕЭ ° q-l 1' 1 1 ООО о т I I1 ê икиь. -•c= • • • • • • • • • • • • • • • • О î I 1 i î i с ï |jl|_ a. Standard Delay Effect ■ OPERATION (D Make all the necessary connections, and set the knobs on the panel as shown below. 06LAV/ SAMPLER EFFECT RANGE/MODE FME/PITCH TRMI*» SAMPLE« MODE O AUTO REC / PLAV ®[]@BML B MANUAL REC/ PLAT SIBPLII/ B TRIG PLAV IlltV B CATE PLAV RSD-10 (2) Set the Level Switch to the appropriate position depending on the device you use. * Usually select the "-20dBm" position, but change to the "-10dBm" if the Overload Indicator lights frequently. (3) Set the delay time you like by using the Delay Time Range Switch Q and the Delay Time Fine Knob. RANGE/MODE FINE/PITCH (ms) @ Set the repetition number of the delay sounds by using the Feedback Level Knob Q- OVERDUB * At MIN position, single delay is obtained. * As you rotate the knob clockwise, oscillation may occur. (5) Adjust the volume of the delay sound with the Effect Level Knob © * At MAX position, the volume of the delay and the direct sounds are equal. b. Special Delay Effect ("Semi-tone Flanging" Effect) The delay time can be controlled by the keyboard. Set the Delay Time Range Switch© to "8ms", and play the keyboard within the range of C5 to C7, then the center frequency of the flanging effect can be controlled in semi-tone steps. EFFECT LEVEL RANGE/MODE * Regarding the tone color and sound range of the keyboard, see page 16 & 25. 3} How to use the Cassette Deck in the Sampler Mode ■ CONNECTIONS AC Adaptor BOSS PSA-120, 220, 240 (Optional) To AC Adaptor Jack U To Other BOSS Micro Studio Series J Foot Switch (FS-1: Optional) -10dBm" —10 O'- 9V DC EFFECT REMOTE О ¿мЬ о TRIG KEY» >ARO ТА € HPUT KUXÉ j All the BOSS Micro Studio Series show the current draw here. Regarding the tone color and sound range of the keyboard, see page 16 & 25. Keyboard Sound Rch Sampled Sound Lch а 1 rt= С шпаптгшч Г~1 n 11 1 гтп nn rm OO a 1! I!1 !! III! Ill II II II III V—"[ V—AO ooooo Do not connect anything to the PAD Jack. * Please be sure to use the Tape Jack together with the Keyboard Jack. (The Tape Jack does not work on its own.) oottmoo Stereo Amplifier Guitar Amplifier ; 0 1 0...