Votos - 2, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
• You can use setting [5] or [6] to switch (or reverse) the drum sounds assigned to Rim 1 and Rim 2. This makes it easier for left-handed drummers to configure their electronic drum kit. 5-4. Pedal Types Steps: MENU ([KIT] + [SONG]) . [5] . [4] . Setting Setting Use the following parameter to specify the types of pedals (i.e., hi-hat controller and kick) connected to your drum module. 1. While holding the [KIT] button, press the [SONG] button to activate Menu Mode. 2. Press number button [5] to select the Trigger Settings parameter group. 3. Press number button [4] to select the Pedal Types parameter. 4. Select a new pedal type combination using the corresponding number button ([1] to [5]). The available settings are as follows. Number Setting button Hi-hat controller Kick pedal [1] Automatic identification [2] HH65 KP65 [3] Hi-hat controller pedal that comes with DTX400K KU100 [4] Hi-hat controller pedal that comes with DTX400K KP65 [5] HH65 KU100 NOTE • This parameter can normally be set to [1] (automatic identification). • When set to [1], the drum module will automatically identify the type of pedal that came with your electronic drum kit when it is turned on. If you then press and hold number button [1], the drum module will flash number button [2] or [3] to indicate the result of automatic identification. • Whenever you change the type of hi-hat controller or kick pedal connected to the drum module, please update this setting using the corresponding number button ([2] to [5]). 48 DTX400K/DTX430K/DTX450K Owner’s Manual Setting Parameters using Menu Mode Setting Parameters using Menu Mode n Steps: MENU ([KIT] + [SONG]) . [5] . [5] . Setting Setting Using the following procedure, you can set the gain level for trigger signals output from individual pads. The higher the gain setting, the louder the sounds produced by light drumming. 1. While holding the [KIT] button, press the [SONG] button to activate Menu Mode. 2. Press number button [5] to select the Trigger Settings parameter group. 3. Press number button [5] to select the Gain parameter. 4. Strike a pad to select it. 5. Enter a new gain level using number buttons [1] to [10/ 0]. Setting 1 to 127 5-6. Minimum Level Steps: MENU ([KIT] + [SONG]) . [5] . [6] . Setting Setting When the strength with which you strike a pad is no more than this level, the pad will not output a trigger signal in response and no sound will be produced. 1. While holding the [KIT] button, press the [SONG] button to activate Menu Mode. 2. Press number button [5] to select the Trigger Settings parameter group. 3. Press number button [6] to select the Minimum Level parameter. 4. Strike a pad to select it. 5. Enter a new setting (%) using number buttons [1] to [10/0]. Setting 0 to 99 (%) n Training Settings 6-1. Timer Steps: MENU ([KIT] + [SONG]) . [6] . [1] . Setting Setting Using the following procedure, you can set the practice timer used in the drum module’s Training Mode. The timer begins counting at the start of a training session, and when the set time is reached, it automatically ends the session. 1. While holding the [KIT] button, press the [SONG] button to activate Menu Mode. 2. Press number button [6] to select the Training Settings parameter group. 3. Press number button [1] to select the Timer parameter. 4. Select your preferred practice time using the corresponding number button ([1] to [10/0]). The available settings are as follows. Number button Setting [1] Off [2] 30 seconds [3] 60 seconds [4] 90 seconds [5] 120 seconds [6] 150 seconds [7] 180 seconds [8] 300 seconds [9] 480 seconds [10/0] 600 seconds NOTE The practice time set using this parameter applies to the following types of training only. • Groove Check •Rhythm Gate • Measure Break • Tempo Up/Down • Change Up • Pad Gate Other types of training are not affected. DTX400K/DTX430K/DTX450K Owner’s Manual 49 Setting Parameters using Menu Mode Setting Parameters using Menu Mode l Steps: MENU ([KIT] + [SONG]) . [6] . [2] . Setting Setting Using the following procedure, you can set the level of training difficulty for Tempo Up/Down (page 33), Change Up (page 34), and Pad Gate (page 37). 1. While holding the [KIT] button, press the [SONG] button to activate Menu Mode. 2. Press number button [6] to select the Training Settings parameter group. 3. Press number button [2] to select the Difficulty Level parameter. 4. Select a new difficulty level using the corresponding number button ([1] to [5]). The higher the level, the more difficult the training. Setting 1 to 5 NOTE The level of difficulty set using this parameter applies only to the Tempo Up/Down, Change Up, and Pad Gate training types. Other types of training are not affected. 6-3. Ignore Timing Steps: MENU ([KIT] + [SONG]) . [6] . [3] . Setting Setting Using the following procedure, you can set the Ignore Timing parameter for Tempo Up/Down (page 33), Change Up (page 34), and Pad Gate (page 37) training. When set to “On”, the pads will produce a sound whenever the...
Otros modelos de este manual:Instrumentos Musicales - DTX400K (4.12 mb)
Instrumentos Musicales - DTX430K (4.12 mb)