Votos - 3, Puntuación media: 4.3
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Parameters are the same as for the Input Channel Parameter View page, minus the GATE and Phase sections and the DELAY MIX and FB GAIN parameters. The parameter settings of the left and right channels of the Stereo Out can be viewed individually. Use the [SEL] buttons to toggle between the left and right channels. Viewing Channel Fader Settings The fader-related settings of the currently selected Input Channel, Bus Out, Aux Send, or the Stereo Out can be viewed and set on the Fader View pages. 1 Use the DISPLAY ACCESS [VIEW] button to select the Fader View page. 2 Use the LAYER buttons to select Layers, and use the [SEL] buttons to select channels. 3 Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] buttons to set them. Pan and Balance controls can be set to center by pressing [ENTER] while they’re selected. 02R96 Version 2—Owner’s Manual Viewing Channel Fader Settings 131 Viewing Channel Fader Settings 131 This is the Fader View page for the Input Channels. PAN: This is the currently selected Input Channel’s Pan parameter. Select this parameter using the cursor buttons, then press the [ENTER] button to set the Pan parameter to Center. See “Panning Input Channels” on page 83 for more information. ON/OFF: This is the On/Off parameter of the currently selected Input Channel. See “Mut ing Input Channels (ON/OFF)” on page 77 for more information. Fader: This indicates the fader position of the currently selected Input Channel. The fader knob appears highlighted when the fader is set to 0.0 dB. The fader position is displayed numerically below the fader. See “Setting Input Channel Levels” on page 79 for more information. SURROUND PAN: The Surround pan parameters for the currently selected Input Channel are displayed only when a Surround mode other than Stereo is selected. See “Using Surround Pan” on page 85 for more information. BUS ROUTING: This section contains Routing and Follow Pan buttons for the currently selected Input Channel. See “Routing Input Channels” on page 82 for more information. The Direct Out output patch can also be set. See “Patching Direct Outs” on page 70 for more information. AUX: These are the currently selected Input Channel’s Aux Send Level, On/Off, and Pre/Post parameters. While a rotary control is selected, the Aux Send can be turned on and off by pressing [ENTER]. See “Aux Sends” on page 98 for more information. Meters: These meters indicate the levels of the currently selected Input Channel and its horizontal or vertical partner. The metering position is displayed below them. GROUP: These buttons indicate which Fader, Mute, EQ, or Comp group, if any, the currently selected Input Channel is in. 02R96 Version 2—Owner’s Manual 132 Chapter 11—Common Channel Functions 132 Chapter 11—Common Channel Functions This is the Fader View page for the Bus Outs. ON/OFF: This is the On/Off parameter of the currently selected Bus Out. See “Muting Bus Outs (ON/OFF)” on page 96 for more information. Fader: This indicates the fader position of the currently selected Bus Out. The fader knob appears highlighted when the fader is set to 0.0 dB. The fader position is displayed numerically below the fader. See “Setting Bus Out Levels” on page 96 for more information. TO ST PAN, ON/OFF & Fader: These are the Bus Out to Stereo Out Pan, On/Off, and Fader parameters for the currently selected Bus Out. The fader knob appears highlighted when the fader is set to 0.0 dB. The fader position is displayed numerically below the fader. See “Sending Bus Outs to the Stereo Out” on page 97 for more information. Meters: These meters indicate the levels of the currently selected Bus Out and its partner. The metering position is displayed below them. GROUP: These buttons indicate which Fader, Mute, EQ, or Comp group, if any, the currently selected Bus Out is in. Aux Sends Below is the Fader View page for the Aux Sends. ON/OFF: This is the On/Off parameter of the currently selected Aux Send. See “Aux Send Pages” on page 99 for more information. Fader: This indicates the fader position of the currently selected Aux Send. The fader knob appears highlighted when the fader is set to 0.0 dB. The fader position is displayed numerically below the fader. See “Settings Aux Send Master Levels” on page 106. Meters: These meters indicate the levels of the currently selected Aux Send and its partner. The metering position is displayed below them. 02R96 Version 2—Owner’s Manual Viewing Channel Fader Settings 133 Viewing Channel Fader Settings 133 rently selected Aux Send is in. Stereo Out Below is the Fader View page for the Stereo Out. The settings of the left and right channels of the Stereo Out can be viewed individually. Use the STEREO [SEL] button to toggle between the left and right channels. BAL: This is the Balance parameter for the Stereo Out. Select this parameter using the cursor buttons, then press the [ENTER] button to set the parameter to Center. See “Balancing the Stere...
Otros modelos de este manual:Instrumentos Musicales - 02R96VCM (3.39 mb)