Votos - 4, Puntuación media: 4.3
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Connect the console to the computer’s USB port directly without using a USB hub. NOTE: If you lose the registration code or access key, you can obtain them again. You will need the PRODUCT ID to do so. Be sure to keep the PRODUCT ID in a safe place after installation. 4 DM2000/02R96/DM1000 Version2 System Software Installation Guide If you are using the DM2000, you must use the following procedure to update FLASH UPDATE (a portion of the system software) before you begin the installation. If you fail to update FLASH UPDATE first, system software installation may fail and the console may malfunction. Installation will initialize data in the DM2000’s user memories. Be sure to back up important data using MIDI Bulk Dump or Studio Manager (refer to the DM2000 Owner’s Manual). After you update Flash Update, install the system software. When you finish updating Flash Update, the DM2000 is temporarily unavailable for operation. 1 Make sure the power to the DM2000 is turned off, then insert the included SmartMedia disk (Firmware) into the card slot on the DM2000. 2 Turn on the power to the DM2000. After counting down, the DM2000 starts updating Flash Update. The updating process takes about 30 seconds. When the update is complete, the DM2000 displays the usual screen. Install the system software. Do not turn off the power during the Flash Update updating process. Direct installation If you can access the Internet directly from your computer, follow the steps below to install the software. See page 8 if you access the Internet from a different computer. The installation procedure will initialize data in the user memories in the console. Be sure to back up important data using MIDI Bulk Dump or Studio Manager. (Refer to the DM2000/02R96/DM1000 Owner’s Manual.) • If you are using the DM2000, update the FLASH UPDATE 2 While holding down the following key on the console, turn on the power of the console. Continue holding down the key until the display blinks “FLASH UPDATE.” DM2000: Transport [REC] key 02R96: MACHINE CONTROL [REC] key DM1000: MONITOR [CLEAR] key 3 Insert the included CD-ROM (Firmware) into the CD-ROM drive. 4 Locate the Upgrade folder on the CD-ROM (“Mac OS 9: Upgrade” for Mac OS 9; “Mac OS X: Upgrade” for Mac OS X), then copy the folder onto the hard disk. Do not run the installer directly from the CD-ROM drive. 5 Double-click “DMUpgrade.exe” (or “****UpgradeE” for Mac OS) in the Upgrade folder that you copied to the hard disk. The installer window opens. 6 Select [Install], then click [Next]. The following window opens. ENGLISH NOTE: The following instruction refers to installing the software in the 02R96 from a connected computer that runs Windows 98SE. However, the basic installation procedure also applies globally to any OS or console. Steps that vary with different operating systems will be explained separately. NOTE: If an error message appears, refer to the Error Message list on page 10. 1 Start the computer and check to see if the following steps are complete. • Installing the Yamaha USB-MIDI Driver in the computer (See the included Studio Manager Installation Guide.) • Connecting the computer and the console using a USB cable • Accessing the Internet from the computer • Backing up the data in the user memories in the console (See the DM2000/02R96/DM1000 Owner’s Manual.) DM2000/02R96/DM1000 Version2 System Software Installation Guide 5 7 7 The following window opens. 8 Select [Create registration code], then click [Next]. The following I/O port setting window opens. 10 The “Console’s FLASH UPDATE is Ver1.” message appears. If your Flash Update has been updated to the latest version, this message does not appear. Instead, a registration code will be displayed; please proceed to step 14. 11 Click [Next]. A message indicating the progress of the update process appears, and Flash Update is updated. The updating process takes about one minute (or five minutes on Mac OS X). 12 The “Completed upgrade for FLASH UPDATE.” message appears. NOTE: A different message (see page 10) may appear in various system environments. In this case, quit the installer following the on- screen instruction. Turn off the power to the console, then press and hold down the [REC] button (on the DM1000, the [CLEAR] key) and turn on the power. The console displays “FLASH UPDATE.” Start the installer and repeat Steps 5 through 9. Proceed to Step 14. 9 Make sure that “YAMAHA USB IN 0-1” is selected for the Input port and that “YAMAHA USB OUT 01” is selected for the output port, then click [Next]. The “Connecting to the console...” message appears and the registration code is created. If you are using Mac OS 9, select “xxxx-1 (xxxx will be the name of the console you are using)” for the Input port, and “xxxx-1 (xxxx will be the name of the console you are using)” for the output port. Note that the port names vary with the OMS setup files. 13 Turn off the power to the console, then press and hold down the [REC] button (on the DM1000...
Otros modelos de este manual:Instrumentos Musicales - 02R96 (323.38 kb)
Instrumentos Musicales - DM2000 (323.39 kb)