Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Perchlorate Material—special handling may apply, See * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate) Windows® is a registered trademark of Microsoft in the U.S.A. and other countries. ¦ ¦ s •Do not place a container with liquid or small metal objects on top of this unit. Liquid or metal objects inside this unit are a fire and electrical shock hazard. •Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result. •Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as marked on the unit. Failure to do so is a fire and electrical shock hazard. •Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock. •Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a fire and electrical shock hazard. •Do not place heavy objects, including this unit, on top of the power cord. A damaged power cord is a fire and electrical shock hazard. In particular, be careful not to place heavy objects on a power cord covered by a carpet. •Be sure to ground the unit to avoid the risk of electrical shock •If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid gets inside the unit, turn it off immediately. Remove the power cord from the AC outlet. Consult your dealer for repair. Using the unit in this condition is a fire and electrical shock hazard. • Should this unit/AC adapter/power supply be dropped or the cabinet be damaged, turn the power switch off, remove the power plug from the AC outlet, and contact your dealer. If you continue using the unit without heeding this instruction, fire or electrical shock may result. •If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a replacement. Using the unit with a damaged power cord is a fire and electrical shock hazard. •Do not remove the unit’s cover. You could receive an electrical shock. If you think internal inspection, maintenance, or repair is necessary, contact your dealer. •Do not modify the unit. Doing so is a fire and electrical shock hazard. •When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. •When rack-mounting the unit, allow enough free space around the unit for normal ventilation. This should be: 10 cm behind, and 20 cm above. •For normal ventilation during use, remove the rear of the rack or open a ventilation hole. •If the airflow is not adequate, the unit will heat up inside and may cause a fire. •This unit has ventilation holes at the rear and bottom to 44.45 31.75 prevent the internal temperature rising too high. Do not block them. Blocked ventilation holes are a fire hazard. 0 5.9 •Hold the power cord plug when disconnecting it from an 4-o6.5 AC outlet. Never pull the cord. A damaged power cord is a potential fire and electrical shock hazard. •Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard. •The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise occurs, relocate the affected equipment. •If the message “WARNING LOW BATTERY!” appears when you turn on this unit, contact your dealer as soon as possible about replacing the internal data backup battery. The unit will still operate correctly, but data other than the presets will be lost. •Before you replace the battery, store your data to an ATA- compliant PC flash storage card via the CS1D, or store the data to the personal computer by connecting the computer to the PC CONTROL “RS-232-C” connector on the DSP1D/DSP1D-EX. •The unit is equipped with the ground connector to avoid the risk of electrical shock. •Be sure to ground the unit before you insert the power plug into an AC outlet. •If the power cord has three pins and the ground connector on the AC outlet is grounded, the unit will be grounded effectively. Operating Notes •The power must be turned on/off using the POWER switch of this unit. Do not turn the power on/off by plugging in the power cable, or by using a power strip or circuit breaker. Doing so may cause malfunctions. •Do not rapidly turn on and off the POWER switch of this unit. Doing so may cause excessive current to damage the system. You must allow at least five seconds to elapse between power-on and power-off. •For this unit, be sure to use a power voltage of the value specified in the Specifications section of this Owner’s Manual. If you apply a higher or lower voltage, a malfunction may result....
Otros modelos de este manual:Instrumentos Musicales - DSP1D (181.14 kb)