Votos - 2, Puntuación media: 5
(
)
)
|
Otros manuales para este modelo:
Instrumentos Musicales - M2500-40C (128.49 kb)
Instrumentos Musicales - M2500-40C (128.49 kb)
Instrumentos Musicales - M2500-40C (4.29 mb)
Resumen del manual
In normal mode You can use the ON/EDIT switch to turn the stereo input channel on/off. When the channel is switched on/off, the ON indicator will be lit/dark to indicate the status. Channels that are switched off will not send any signals to the GROUP, STEREO. MONO/C, or AUX buses, but you can still use the PFL switch (M) to monitor the signal from the MONITOR OUT jacks or the PHONES jack. In check mode When a scene is selected, the on/off status memorized in that scene will be indicated by the lit/dark status of the CHECK indicator. In check mode, you can also use the ON/EDIT switch to switch the CHECK indicator between lit/dark. For details on check mode, refer to page 32. K PEAK/NOM/SIGNAL indicators These three indicators allow you to check the pre- fader signal level of the stereo input channel. • PEAK indicator This will light when the signal mixed to monaural exceeds nominal level by 17 dB. • NOM (nominal) indicator This will light when the signal mixed to monaural reaches nominal level (0 dB). • SIGNAL indicator This will light when the signal mixed to monaural reaches a level 13 dB below nominal. L Channel fader This adjusts the output level of the stereo input channel signal. This fader affects the level of the signal that is sent to the GROUP, STEREO, MONO/C, and AUX (if the PRE switch is off) buses. M PFL (pre-fader listen) switch When this switch is on ( ), the pre-fader signal will be sent to the MONITOR INPUT PFL bus, and can be monitored from the MONITOR OUT and PHONES jacks. M2500—Owner’s Manual 7 Control panel Control panel 9 MONITOR INPUT MASTER PFL AFL LR MONO ST LR L INPUT A R ST CH 1 L INPUT B R L/MONO ST CH 2-4 INPUT R MONOSTON (PFL) Same as ST CH 1 ST CH 2-4 from CPU AUX 11-14 Same as AUX 3-6 AUX 7-10 Same as AUX 3-6 B A ST LRMONOLR MONO/CSTEREO BAL ON CHECK 2 stage EQ 2 stage EQ 2 stage EQ 2 stage EQ GAIN B GAIN A AUX 14 13 12 11 10 9 2 3 4 5 6 7 8 1 GROUP 8 7 6 5 4 3 2 1 EQHILOGAIN SIGNAL PFL LOHIEQ AUX1 PRE AUX2 AUX3 AUX4 AUX5 AUX6 ST MONO PEAK NOM Control ON/EDIT 2 L 7 M 6 J ON 8 M2500—Owner’s Manual Control panel Control panel AUX 1–6 section 1 10 10 10 10 10 10 ON ON ON ON ON ON 5 5 5 5 5 5 0 0 0 0 0 0 5 5 5 5 5 5 10 10 10 10 10 10 20 20 20 20 20 20 30 30 30 30 30 30 40 40 40 40 40 60 50 60 40 50 60 50 60 50 60 50 60 50 AFL AFL AFL AFL AFL AFL AUX1 AUX2 AUX3 AUX4 AUX5 AUX6 23 These are the output channels that control the signals of AUX buses 1–6. The signals that have passed through these output channels will be output individually from the AUX OUT 1–6 jacks (page 27). In addition, they pass through the MONITOR MASTER PFL/AFL buses and can be monitored from the MONITOR OUT L/R and the PHONES jacks. AON switches These turn AUX OUT 1–6 on/off. When a switch is on ( ), the signal of the corresponding AUX bus will be output to the AUX OUT jack. BAUX 1–6 master faders These adjust the output levels of AUX OUT 1–6. CAFL (after fader listen) switches These switches are used to monitor the signal of the AUX OUT 1–6 section from the MONITOR OUT/ PHONES jacks. When an AFL switch is on (the switch above the indicator will light), the pre/afterfader signals of the AUX 1–6 section will be sent to the MONITOR MASTER PFL/AFL buses respectively, and can be monitored via the MONITOR OUT/PHONES jacks. At this time, you can use the MASTER PFL switch (page 19) in the monitor section to select whether you will monitor the pre- or after-fader signal. Note: If the PFL switch of even one input channel is turned on, the signal of the MONITOR INPUT bus will take priority for monitoring. In this case, be aware that even if the AFL switch is turned on, the MONITOR MASTER bus cannot be monitored. MONITOR INPUT MASTER (PFL) PFL AFL MONO ST LR ONMONO ST LR MONO ST LR AUX 1 3 5 7 91113 ON to METER Same as AUX 1 AUX 2-6 AUX 1 1 INSERT I/O 0dB AUX OUT +4dB AFL ON 1412102 4 6 8 2 1 3 M2500—Owner’s Manual 9 Control panel Control panel n 1 2 These output channels control the signals of AUX buses 7–14 or GROUP buses 1–8. You can use the GROUP/AUX FLIP switch (page 14) to select the signals that will be controlled. GROUP/AUX FLIP switch= GROUP ( ) The signals of AUX buses 7–14 will be sent to channels A7/G1–A14/G8 respectively, and will be output individually from the AUX/GRP OUT A7/G1–A14/ G8 jacks. A7 / G1 AFL LEVEL 0 10 ON A8 / G2 AFL LEVEL 0 10 ON 0 10 AUX5 AUX6 PRE 0 10 0 10 0 10 0 10 AUX7 AUX10 AUX9 AUX8 A7 / G1 AFL LEVEL 0 10 ON A8 / G2 AFL LEVEL 0 10 ON A9 / G3 AFL LEVEL 0 10 ON A10 / G4 AFL LEVEL 0 10 ON A11 / G5 AFL LEVEL 0 10 ON A12 / G6 AFL LEVEL 0 10 ON A13 / G7 AFL LEVEL 0 10 ON A14 / G8 AFL LEVEL 0 10 ON 3 ALEVEL control This adjusts the output level of AUX/GRP OUT A7/ G1–A14/G8. The “” position is nominal level. B ON switch This turns AUX/GRP OUT A7/G1–A14/G8 on/off. When the switch is on ( ), the signals from the A7/ G1–A14/G8 section will be output from the AUX OUT A7/G1–A14/G8 jacks respectively. C AFL switch This switch is used to monitor the signal from the AUX/GRP OUT A7/G1–A14/G8 section v...
Otros modelos de este manual:Instrumentos Musicales - M2500-24 (1.64 mb)
Instrumentos Musicales - M2500-32 (1.64 mb)
Instrumentos Musicales - M2500-48C (1.64 mb)
Instrumentos Musicales - M2500-56C (1.64 mb)