Votos - 1, Puntuación media: 3
(
)
)
|
Otros manuales para este modelo:
Instrumentos Musicales - M2500-48C (128.49 kb)
Instrumentos Musicales - M2500-48C (128.49 kb)
Instrumentos Musicales - M2500-48C (4.29 mb)
Resumen del manual
When an AFL switch is on (the switch above the indicator will light), the pre/afterfader signals of the AUX 1–6 section will be sent to the MONITOR MASTER PFL/AFL buses respectively, and can be monitored via the MONITOR OUT/PHONES jacks. At this time, you can use the MASTER PFL switch (page 19) in the monitor section to select whether you will monitor the pre- or after-fader signal. Note: If the PFL switch of even one input channel is turned on, the signal of the MONITOR INPUT bus will take priority for monitoring. In this case, be aware that even if the AFL switch is turned on, the MONITOR MASTER bus cannot be monitored. MONITOR INPUT MASTER (PFL) PFL AFL MONO ST LR ONMONO ST LR MONO ST LR AUX 1 3 5 7 91113 ON to METER Same as AUX 1 AUX 2-6 AUX 1 1 INSERT I/O 0dB AUX OUT +4dB AFL ON 1412102 4 6 8 2 1 3 M2500—Owner’s Manual 9 Control panel Control panel n 1 2 These output channels control the signals of AUX buses 7–14 or GROUP buses 1–8. You can use the GROUP/AUX FLIP switch (page 14) to select the signals that will be controlled. GROUP/AUX FLIP switch= GROUP ( ) The signals of AUX buses 7–14 will be sent to channels A7/G1–A14/G8 respectively, and will be output individually from the AUX/GRP OUT A7/G1–A14/ G8 jacks. A7 / G1 AFL LEVEL 0 10 ON A8 / G2 AFL LEVEL 0 10 ON 0 10 AUX5 AUX6 PRE 0 10 0 10 0 10 0 10 AUX7 AUX10 AUX9 AUX8 A7 / G1 AFL LEVEL 0 10 ON A8 / G2 AFL LEVEL 0 10 ON A9 / G3 AFL LEVEL 0 10 ON A10 / G4 AFL LEVEL 0 10 ON A11 / G5 AFL LEVEL 0 10 ON A12 / G6 AFL LEVEL 0 10 ON A13 / G7 AFL LEVEL 0 10 ON A14 / G8 AFL LEVEL 0 10 ON 3 ALEVEL control This adjusts the output level of AUX/GRP OUT A7/ G1–A14/G8. The “” position is nominal level. B ON switch This turns AUX/GRP OUT A7/G1–A14/G8 on/off. When the switch is on ( ), the signals from the A7/ G1–A14/G8 section will be output from the AUX OUT A7/G1–A14/G8 jacks respectively. C AFL switch This switch is used to monitor the signal from the AUX/GRP OUT A7/G1–A14/G8 section via the MONITOR OUT/PHONES jacks. If all the input channel PFL switches are off, you can turn on this AFL switch to monitor the corresponding signal of the A7/G1–A14/G8 section from the MONITOR OUT/PHONES jacks. You can use the MASTER PFL switch of the monitor section to switch the monitor signal between pre/post-fader (LEVEL control). GROUP/AUX FLIP switch= AUX ( ) The signals of GROUP buses 1–8 will be sent to channels A7/G1–A14/G8 respectively, and output individually from the AUX/GRP OUT A7/G1–A14/G8 jacks. A7 / G1 AFL LEVEL 0 10 ON A8 / G2 AFL LEVEL 0 10 ON PAN ST L C R ODD EVEN MONO LCR 1-2 3-4 5-6 7-8 10 M2500—Owner’s Manual Control panel Control panel n 4 5 6 7 8 G1 / A7 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G2 / A8 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G3 / A9 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G4 / A10 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G5 / A11 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G6 / A12 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G7 / A13 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G8 / A14 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON These are the output channels that control GROUP buses 1–8 or AUX buses 7–14. Use the GROUP/AUX FLIP switch (page 14) to select which signals will be controlled. GROUP/AUX FLIP switch= GROUP ( ) The signals of GROUP buses 1–8 will be sent to channels G1/A7–G8/A14 respectively, and will be output individually from the GRP/AUX OUT G1/A7–G8/ A14 jacks. PAN ST L C R ODD EVEN MONO LCR 1-2 3-4 5-6 7-8 G1 / A7 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G2 / A8 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON M2500—Owner’s Manual 11 Control panel Control panel GROUP/AUX FLIP switch= AUX ( ) The signals of AUX buses 7–14 will be sent to channels G1/A7–G8/A14 respectively, and will be output individually from the GRP/AUX OUT G1/A7–G8/ A14 jacks. G1 / A7 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON G2 / A8 ON/EDIT AFL 10 10 20 30 40 60 50 5 0 5 PAN L C R MATRIX ST MONO LCR CHECK ON 0 10 AUX5 AUX6 PRE 0 10 0 10 0 10 0 10 AUX7 AUX10 AUX9 AUX8 D PAN control This adjusts the pan of the signal that is sent from the G1/A7–G8/A14 section to the STEREO or MONO/C bus. The function of the PAN control will change as follows, depending on the setting of the channel assign switch (5). When the ST switch is on PAN will adjust the pan of the signal that is sent from each channel to the STEREO L/R bus. When the LCR switch is on PAN will adjust the pan of the signal that is sent from each channel to the STEREO L/R bus and MONO/C bus. E Channel assign switches These switches assign the post-fader post-PAN signal to the desired bus. • ST (stereo) switch If this switch is on ( ), ...
Otros modelos de este manual:Instrumentos Musicales - M2500-24 (1.64 mb)
Instrumentos Musicales - M2500-32 (1.64 mb)
Instrumentos Musicales - M2500-40C (1.64 mb)
Instrumentos Musicales - M2500-56C (1.64 mb)