Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
7 Check the radio button to the left of “Install the software automatically (Recommended).” Click [Next]. The system starts the installation. n If during the installation the system displays “...has not passed Windows Logo testing to verify its compatibility with Windows XP,” click [Continue Anyway]. 8 When the installation is complete, the system displays “Completing the Found New Hardware Wizard.” Click [Finish]. (The Wizard window may take a while to display on some computers.) 9 Restart the computer. If the system displays “Found New Hardware” in the lower right corner, wait until “System Settings Change” is displayed. (The Wizard window may take a while to display on some computers.) The USB-MIDI driver installation is complete. After this, when you install the USB-MIDI driver, always make sure that the driver satisfies the version requirements: Version 2.2.2 or later. Installing an older USB-MIDI driver may cause computer malfunction or freezing when the Tyros3 is connected. This problem may occur particularly when installing the driver from a CD-ROM included in a Yamaha product other than the Tyros3. We recommend that always use the latest driver downloaded from the website (download). • Installing the driver on Windows Vista 1 Start the computer and use the “Administrator” account to log on to Windows Vista. 2 Insert the included CD-ROM into the CD-ROM drive. 3 First, make sure the POWER switch on the instrument is set to OFF, then use a USB cable to connect the USB connector of the computer to the USB TO HOST connector of the instrument. When the instrument is turned on, the computer automatically displays the “Found New Hardware” window. Click “Locate and install driver software (recommended)”. If the window is not displayed automatically, refer to “Troubleshooting.” (Some computers may take a while to display the window.) n If the “User Account Control” window appears, click [Continue]. 4 If a message allowing Windows to search online for driver software appears, click “Don’t search online.” 5 If a message prompting you to insert the disk that came with your device appears, click [Next]. The system starts the installation. n If the “Windows Security” window appears, confirm this software is authored by Yamaha Corporation then click [Install]. 6 When the installation is complete, the system displays the message “The software for this device has been successfully installed.” Click [Close]. (Some computers may take a while to display the window.) The USB-MIDI driver installation is complete. After this, when you install the USB-MIDI driver, always make sure that the driver satisfies the version requirements: Version 3.0.2 or later. Installing an older USB-MIDI driver may cause computer malfunction or freezing when the Tyros3 is connected. This problem may occur particularly when installing the driver from a CD-ROM included in a Yamaha product other than the Tyros3. We recommend that always use the latest driver downloaded from the website (download). Voice Editor Once you’ve install the Voice Editor, you can use your computer to edit the Voices of the Tyros3. 1 Double-click on the “VoiceEditor_” folder in the CDROM. The file “Setup.exe” will be displayed. 2 Double-click on the “Setup.exe” file. The setup dialog will be displayed. 3 Execute the installation by following the on-screen directions. For subsequent operations, refer to the PDF owner’s manual for the Voice Editor. 4 Tyros3 Accessory CD-ROM Installation Guide Troubleshooting The driver cannot be installed. • Is the USB cable connected correctly? >Check the USB cable connection. >Disconnect the USB cable, then connect it again. • Is the USB function enabled on your computer? >When you connect the instrument to the computer for the first time, if the “Add New Hardware Wizard” does not appear, the USB function on the computer may be disabled. Perform the following steps. 1 Select [Control Panel]* > [System] > [Hardware] > [Device Manager] (for Windows XP), or select [Control Panel]* > [Device Manager] (for Windows Vista). * Classic View only. 2 Make sure that no “!” or “x” marks appear at “Universal serial bus controller” or “USB Root Hub.” If you see an “!” or “x” mark, the USB controller is disabled. • Is any unknown device registered? >If driver installation fails, the instrument will be marked as an “Unknown device,” and you will not be able to install the driver. Delete the “Unknown device” by following the steps below. 1 Select [Control Panel]* > [System] > [Hardware] > [Device Manager] (for Windows XP), or select [Control Panel]* > [Device Manager] (for Windows Vista). * Classic View only. 2 Look for “Other devices” in the menu “View devices by type.” 3 If you find “Other devices,” double-click it to extend the tree to look for “Unknown device.” If one appears, select it and click the [Remove] button. 4 Remove the USB cable from the instrument, and make the connection again. 5 Install th...