Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
When you press the PROGRAM BUTTON (23), all the channel LED’s will flash indicating the scene has been stored into memory. The right two digits in the LCD DISPLAY (6) will advance to the next available step. 6.You may continue this pattern up to 99 times per each CHASE PATTERN. You may mix and match the top and bottom channel buttons together in a CHASE PATTERN, however, remember that the upper and lower channels chase speeds are controlled separately. 7.When you have completed programming all your steps you must record an “End Step” to finalize your CHASE PATTERN. To program the “End Step,” press and hold down the SHIFT BUTTON (16). While holding down the SHIFT BUTTON (16), press and release the PROGRAM BUTTON (23). You will see all the LEDs flash indicating the “End Step” was successfully programmed. 8. To exit the program mode, press and hold the PROGRAM BUTTON for two (2) seconds. Running Chase Patterns: This function allows you to automatically run one of the 60 CHASE PATTERNS. The speed of these chase’s can be controlled by the DIMMER SPEED (9) and SWITCH SPEED (10) faders. The DIMMER SPEED (9) will control channels 1-8 and SWITCH SPEED will control channels 9-16. To run a chase pattern: 1.Press the CHASE BUTTON (24). The chase LED in the LCD Display (6) will light indicating you are in CHASE MODE. 2.Use the PATTERN BUTTONS (18 & 19) to select the CHASE PATTERN you wish to run. 3.Use the SPEED CONTROLS (9 & 10) to adjust your chase speed and the LEVEL CONTROL (8) to set your output intensity. Using the Built In Programs: This controller comes with 30 preset programs. These programs are designed to get you up and running in minutes. Programs 31-40 control channels 1-8, 41-50 control channels 9-16, and programs 51-60 combine channels 1-16. Chase Pattern 40 is a combination of 31 -39. Chase Pattern 50 is a combination of 41 -49. Chase Pattern 60 is a combination of 51-59. These chases can not be changed or edited. ©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 10 Cross Mode: Cross mode is a manual adjustment that fades from one step to the next. You may use this function in any CHASE PATTERN. This function will not effect channels 9-16. To use this function: 1 .Be sure you are in CHASE MODE. 2.Turn CROSS MODE on by holding down the SHIFT BUTTON (16), and pressing the CROSS SETUP BUTTON (20) until the yellow CROSS ON LED glows. 3.Press the CROSS BUTTON (15) to activate the cross function. Channels 1-8 will stop chasing and the MASTER FADER (4) LED will turn off. Either the “A” or “B” LED on the MASTER FADER (4) will begin to glow depending on the position of the fader. 4.You may now use the MASTER FADER (4) to manually cross fade through a CHASE PATTERN’S steps. Sliding the MASTER FADER (4) up and down will change the steps from one to the next. The slower you move the fader the slower the scenes will fade from one to the next. 5.In this operation, the FADE TIME (7) level will function. 6.You may use the CHASE PATTERN BUTTONS (18 & 19) to select a different chase at any time. Loop Mode: This function allows you to group several CHASES together and run them in a sequential repeating pattern. 1 .Be sure you are in CHASE MODE. 2.Go to the first pattern you wish to program into the loop and press the LOOP BUTTON (22). After you press the LOOP BUTTON (22), the channel green LEDs will flash and “LP” will be displayed in the right two (2) digits in the LCD DISPLAY (6). 3.Repeat step two until you have enter all your desired CHASE PATTERNS. If the LOOP BUTTON (22) is not pressed within 10 seconds, the loop will automatically start to cycle. You may add the same CHASE PATTERN more than once. 4.When you have finished entering all you chases, wait 10 seconds and “CL’ will appear in the right two digits of the LCD DISPLAY (6). When this happens the chases will automatically begin to run and loop in the same pattern you programmed them in. 5.To cancel or exit this mode, press the LOOP EXIT BUTTON (22) while holding down the SHIFT BUTTON (16). Show Mode: This function gives you manual control over channels 1-8 when running in normal chase mode. This function will not effect channels 9-16 in any way. To operate in show mode: ©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 11 1 .Run a chase in a normal fashion. 2.Bring the DIMMER SPEED SLIDER (9) down until “SHO” appears in the LCD DISPLAY (6). 3.When “SHO” appears you may use the STEP UP and DOWN BUTTONS (20 &21) to manually step through a CHASE PATTERNS. 4.In this function you may change your selected CHASE PATTERN at any time. Deleting Chases: This function allows you to delete an unwanted CHASE PATTERN. Please note that only CHASE PATTERNS 1 -30 can be deleted, 31 -60 are built in programs and can not be deleted or changed in any way. Also note that a program is never completely erased unless you initialize the controller. The program will simply not be able to be executed. It...