Votos - , Puntuación media:
(
)
)
Fabricar: Dell
Tamaño del archivo: 1.19 mb
Nombre del archivo:
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
NOTE: You must detach the antenna cables from the Mini PCI Card before you remove the display module. 1 M2.5 x 6-mm screws (2) 1 M2.5 x 6-mm screws (2) NOTE: Make sure that the antenna cables are disconnected from the Mini PCI Card before removing the display module. 12. Disconnect the signal cable from the system board. 13. If a tape secures the signal connector, remove it and disconnect the signal cable from the system board. 14. Remove the display module out of the bottom case. Replacing the Display 1. Replace the display module into the bottom case and open the display 180 degrees. 2. Replace the two M2.5 x 6-mm screws on the back of the computer. 3. Connect the speaker cable connector. 4. Connect the display cables on the left and right sides of the unit. 5. Connect the antenna cables. 6. Carefully thread the antenna cable back into place and connect both antenna connectors, matching the color codes. 1 display cable tab 2 display module 3 speaker cable connector 4 display cable connector NOTICE: Do not pull on the signal cable. Pull the signal connector to disconnect the cables. 7. Connect the signal cable to the system board. 8. If a tape secured the signal connector, replace it and connect the signal cable to the system board. 9. Close the display and turn the computer over. 10. Replace the two M2.5 x 6-mm screws from the bottom of the computer. 11. Replace the upper memory module cover and tighten the two captive screws. 12. Replace the keyboard. 13. Replace the battery. Back to Contents Page Back to Contents Page Cooling Fan Dell™ Inspiron™ 700m/710m Service Manual Removing the Cooling Fan Removing the Cooling Fan 1. Remove the battery. 2. Remove the keyboard. 3. Disconnect the black and white antenna cables from the Mini PCI Card. 4. Remove the display module. 5. Remove the palm rest. 6. Remove the system board. 7. Remove the three M2 x 3-mm screws that secure the cooling fan to the system board. 8. Remove the tape that secures the cooling fan cable to the fan. 9. Disconnect the cooling fan cable from the system board connector. 10. Lift the cooling fan up and out of the bottom case. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: Disconnect the computer and any attached devices from electrical outlets. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Before Working Inside Your Computer" before performing the following procedure. 1 system board connector 2 cooling fan connector 3 cooling fan 4 M2 x 3-mm screws (3) NOTICE: Do not pull on the cooling fan cable. Pull from the cooling fan connector to disconnect the cable. Back to Contents Page Back to Contents Page Hard Drive Dell™ Inspiron™ 700m/710m Service Manual Replacing the Hard Drive Returning a Hard Drive to Dell Replacing the Hard Drive 1. Remove the battery. 2. Loosen the three captive screws that secure the hard drive to the bottom case. 3. Loosen the two captive screws on the hard-drive securing bracket and remove the bracket. 4. Pull the hard drive out of the computer using the pull tab. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: Disconnect the computer and any attached devices from electrical outlets. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Before Working Inside Your Computer" before performing the following procedure. NOTE: Rubber grommets secure each screw to the hard drive so that you do not need to completely remove the screws. 1 captive screws (3) 2 hard drive cover NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging. See "Protecting Against Electrostatic Discharge" in the Product Information Guide. 5. Remove the new drive from its packaging. Save the original packaging for storing or shipping the hard drive. 6. Insert the new drive at a 45-degree angle and rotate the drive into place. 7. Press on the connector until the drive is fully seated. 1 hard-drive securing bracket 2 pull tab 3 hard drive NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector. 8. Replace the hard-drive securing bracket and tighten the two captive screws. 9. Replace the hard drive cover and tighten the three captive screws. 10. Install the operating system for your computer. 11. Install the drivers and utilities for your computer. Returning a Hard Drive to Dell Return your old hard drive to Dell in its original or comparable foam packaging. Otherwise, the hard drive may be damaged in transit. Back to Contents Page 1 foam packaging 2 hard drive Back to Contents Page Keyboard Dell™ Inspiron™ 700m/710m Service Manual Removing the Keyboard Replacing the Keyboard Removing the ...