Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
3. Remove the display assembly. 4. Remove the keyboard. 5. Remove the palm rest. 6. Remove the M2.5 x 5-mm screw from the top left corner of the fan. 7. Disconnect the fan cable connector. 8. Lift the fan straight up out of the computer. When replacing the fan, follow the steps in reverse order. Back to Contents Page CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 M2.5 x 5-mm screw Back to Contents Page Fans Dell™ Latitude™ D810 Service Manual Removing the Microprocessor Fan 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the display assembly. 3. Remove the keyboard. 4. Remove the palm rest. 5. Remove the M2.5 x 5-mm screw from the top left corner of the fan. 6. Disconnect the fan cable connector. 7. Lift the fan straight up out of the computer. Removing the Video Card Fan 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the display assembly. 3. Remove the keyboard. 4. Remove the palm rest. CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 M2.5 x 5-mm screw 2 fan cable connector 5. Remove the M2.5 x 5-mm screw from the bottom right corner of the fan. 6. Disconnect the fan cable connector. 7. Lift the fan straight out of the computer. Back to Contents Page 1 M2.5 x 5-mm screw 2 fan cable connector Back to Contents Page Hard Drive Dell™ Latitude™ D810 Service Manual Removing the Hard Drive and Carrier 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Turn the computer over. Use a standard #1 Phillips screwdriver to remove the two M3 x 3- mm screws. 3. Slide the hard drive out of the computer. Removing the Hard Drive From the Carrier 1. Use spring tension to gently pry the carrier open near the connector at the back of the carrier. 2. Lift the hard drive out of the carrier. CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before working inside your computer, read the safety instructions in your Product Information Guide. NOTICE: To prevent data loss, shut down your computer before removing the hard drive. Do not remove the hard drive while the computer is on, in standby mode, or in hibernate mode. NOTICE: Hard drives are extremely fragile; even a slight bump can damage the drive. NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell. NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging. See "Protecting Against Electrostatic Discharge" in your Product Information Guide. CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. Back to Contents Page Back to Contents Page Keyboard Dell™ Latitude™ D810 Service Manual 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Turn the computer top-side up and open it. 3. Remove the center control cover. 4. Remove the keyboard: a. Remove the two M2.5 x 5-mm screws across the top of the keyboard. b. Lift the keyboard and slide it toward the back of the computer to disengage the tabs. c. Hold the keyboard up at an angle and slightly back to allow access to the keyboard connector. d. Pull up on the keyboard connector tab to disconnect the keyboard connector from the system board. CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 display 2 center control cover 3 computer base NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time-consuming to replace. Be careful when removing and handling the keyboard. Back to Contents Page 1 M2.5 x 5-mm screws (2) 2 keyboard 3 palm rest 4 keyboard tabs (5) Back to Contents Page Palm Rest Dell™ Latitude™ D810 Service Manual 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the display assembly. 3. Remove the keyboard. 4. Remove the 13 M2.5 x 8-mm screws from the bottom of the computer. 5. Remove the four M2.5 x 5-mm screws labeled "P" from the top of the palm rest. 6. Disconnect the system board connector from the system board. 7. Disconnect the touch pad connector from the system board. CAUTION: Before performing the following procedures, read the safety instructions in yo...