Votos - 0, Puntuación media: 4
(
)
)
|
Resumen del manual
LUBRICATION CHANGE FOR FRONT DIFFERENTIAL, TRANSMISSION, AND REAR DIFFERENTIAL Use the lower plug (2) for drainage (Figure 30, Figure 31, or Figure 32). Remove both plugs to allow the lubricant to drain faster. See preceding NOTE. Metal particles may be discovered in the fluid or on the magnetic drain plug when changing the differential or transmission fluid. These particles are normal and expected for the first few fluid changes. This is a result of the gears being “net forged”, meaning the gears are forged to a shape very close to the final gear size but the teeth are not finish machined prior to assembly. The “finish machining” occurs when the gears make contact under load during vehicle operation. The magnetic drain plug is included in the design to collect the metal particles generated from the gear break in process. This is an established process and is not detrimental to gear service life. Front differential: Clean and install the drain plug (2) and washer before filling the front differential with new lubricant (Figure 30). Tighten the drain plug to 108 in-lb (12 N·m). Use a funnel when filling the front differential through the lubricant level indicator hole (1). See Periodic Lubrication Schedule on page 36.Tighten the level indicator plug to 120 in-lb (14 N·m). Page 44 HUV 4421 Owner’s Manual Gearcase Lubrication 12 12 215 216 Figure 30 Front Differential Lubrication Level Figure 31 Transmission Lubrication Level Transmission: Clean and install the drain plug (2) before filling the transmission with new lubricant (Figure 31). Tighten the drain plug to 96 in-lb (11 N·m). Remove the fill plug from the top of the transmission case and use a funnel to fill the transmission with lubricant. See Periodic Lubrication Schedule on page 36. Apply Loctite 567 to the threads of the fill plug and tighten to 21 ft-lb (28 N·m). Check the level of lubricant at the level indicator plug (1). Apply Loctite 567 to the threads of the level indicator plug and tighten to 21 ft-lb (28 N·m). Rear differential: Clean and install the drain plug (2) and washer before filling the rear differential with new lubricant (Figure 32). Tighten the drain plug to 96 in-lb (10.8 N·m). Use a funnel to fill the differential through the lubricant level indicator hole (1). See Periodic Lubrication Schedule on page 36. Apply Loctite 567 to the threads of the level indicator plug and tighten to 21 ft-lb (28 N·m). HUV 4421 Owner’s Manual Page 45 Engine Coolant – Diesel Vehicles 12 Figure 32 Rear Differential Lubrication Level ENGINE COOLANT – DIESEL VEHICLES ENGINE COOLANT LEVEL CHECK The coolant reserve tank (2) is located under the hood on the passenger side (Figure 17). Raise the hood to check the coolant level before every operation. 1. Check the coolant level of the reserve tank (2). If the coolant is at or below the LOW mark, add pre-mixed coolant until the level reaches the FULL mark. If a leak is detected, have it checked by a trained technician. See following WARNING. WARNING • Hot! Coolant reserve tank is pressurized. Do not remove cap when engine is hot. Page 46 HUV 4421 Owner’s Manual Air Intake System AIR INTAKE SYSTEM CAUTION • Do not drill into the driver-side frame. Failure to heed this caution could damage the engine byallowing excessive contamination to enter the air intake system. AIR FILTER REPLACEMENT The air filter should be inspected periodically and replaced when necessary. Filter changes should not exceed the recommended interval. See Periodic Service Schedule on page 33. More frequent service may be required in extremely dirty operating environments. In the event of a loss of power, sluggish acceleration, or a roughly running engine, service the air filter immediately. Air Filter Removal 1. Raise the cargo bed, and locate the air filter canister. 2. Release both canister tab locks (Figure 33). 3. Pull the canister cap away from the canister. 4. Remove the air filter cartridge (1). See following NOTE. NOTE: The air filter cartridge is specifically designed for this engine. It only fits into the canister one way. Use only the Husqvarna part (P/N 603 00 00-10) designed for this engine. 1 Figure 33 Air Filter Cartridge Air Filter Installation 1. Push the new air filter cartridge onto the nozzle inside the canister. 2. Place the canister cap, marked TOP, on the top center of the canister. 3. Secure the canister cap with both tab locks. HUV 4421 Owner’s Manual Page 47 Fueling Instructions FUELING INSTRUCTIONS See General Warnings on page 11. DANGER • Turn the key switch to the OFF position before fueling. • Do not pour fuel into the fuel tank when the engine is hot or while it is running. • To avoid electric arc caused by static electricity, the fuel storage/pumping device must be grounded. Ifthe pump is not grounded, the vehicle must be grounded to the pump before and during the fuelingoperation. • To avoid the possibility of fire, clean up any spilled fuel before operating the vehicle. 1. Remove the fuel cap and fill the ...
Otros modelos de este manual:Equipo para la TC - HUV 4421 4421-G/GX/GXL (5.03 mb)