Iniciar sesión:
Votos - 4, Puntuación media: 3.5 ( )

Manual de usuario iOptron, modelo SmartStar 8600

Fabricar: iOptron
Tamaño del archivo: 574.13 kb
Nombre del archivo: 4d400bae-71ca-42b7-9599-c1ee22f52341.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Extend tripod legs to full extension. 2. Slide tray on bottom of shaft (#7). Then screw on round black knob (#9). Step 2. Attaching the Mount 1. Raise wedge plate on the tripod by turning two tilt locks (12); 2. Attach mount to wedge plate using supplied azimuth lock screw (10). 3. lower wedge plate to it’s lowest position by turning the upper tilt lock upward while lightly push the mount down. Secure the mount by tightening the lower lock. Step 3a. Installing Batteries Note: you may use 8 AA batteries (Step 3a and 3b) or the AC adaptor (Step 5) to operate the mount. Carefully remove the battery compartment cover (shown) open. Gently pull the battery holder out of the compartment (see photo in Step 3b) to avoid breaking the attached wires. Step 3b. Insert 8 AA batteries (not included) in the holder. Refer to the diagram on the holder to orient the batteries properly. Replace the holder back into the battery compartment and replace the lid. For reference: the battery pack fits in with wires on the bottom right (See arrow in photo). Use only fresh batteries. Using/mixing old or low batteries may cause error messages. #2 knob Step 4. Attaching TelescopeAttach telescope to mount using dovetail lock knob (#2). (Picture shows 80mm refractor. However all scopes will attach in the same manner.) iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569.0200 | Toll Free (866) 399.4587 | Plug in AC adaptor here Step 5. Plug in hand controller and AC adaptor. Plug hand controller into either one of the two HBX ports on the mount. Next plug in AC adaptor. (Or use batteries—see step 3). Turn on power (the red light should go on). At this point you can begin observing manually. Use the 4 Arrow keys (^Ў<>) on the hand controller to rotate the scope Up, Down, Left, and Right. Use the SPEED key to change the slew rate from the slowest (1X) to the fastest (MAX). The next steps show you how to set up the telescope and controller for automatic slewing and tracking. Step 6. Set up telescope for auto-observing. Level the mount using the bubble on side of mount by adjusting tripod legs. The bubble should be in the middle of the circle. It is also suggested to use additional levels (such as a torpedo level) to assure precise leveling. 1) South 2) Up #4 Alt lock Step 7. Park Position for Altazimuth Operation Set telescope to PARK POSITION. (1) Position the mount so that the “SOUTH” mark is facing south (A compass may be helpful). (2) The telescope tube should be pointed directly up at the zenith. If it is not perfectly straight then loosen the altitude lock (#4) to adjust telescope. Please refer to full manual for German equatorial operation. Step 8. Main Screen Turn on the mount and wait for controller to display “GPS-OK” in top right corner —not “GPS-ON”. GPS provides Latitude, Longitude, and current time only. Step 9. Press the MENU key once. Scroll (with the ^/Ў keys) to “Set Up Controller” Press ENTER. Then go to Set Up Local Time and Site in ...

Otros modelos de este manual:
Instrumentos de óptica - SmartStar 8602 (574.13 kb)
Instrumentos de óptica - SmartStar 8603 (574.13 kb)
Instrumentos de óptica - SmartStar 8604 (574.13 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría