Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
To quit random playback, press CD/RANDOM again. PROGRAMMING 1 Press CD/RANDOM to enter CD mode. 2 Press PROGRAM/CLOCK SET in stop mode. The PROG indicator starts blinking in the display window. CD PROG 3 Press 4 or . to select a desired track to be programmed while the PROG indicator is blinking. Track to be programmed CD PROG 4 Press PROGRAM/CLOCK SET while the PROG indicator is blinking. 5 Repeat steps 3 and 4 to program other tracks. 6 Press PLAY/PAUSE 3/8 while the PROG indicator is blinking. The tracks are played in the order you have programmed. Stopping programmed playback Press STOP 7. The PROG indicator goes off and the unit exits from programmed playback. Checking the program contents Before starting programmed playback, press PROGRAM/CLOCK SET. Each time you press the button, the programmed tracks are shown in the display window. Adding tracks in the program 1 Press PROGRAM/CLOCK SET repeatedly until “00” appears as a track number. 2 Press 4 or . to select a new track number, then press PROGRAM/CLOCK SET. Editing the program 1 Press PROGRAM/CLOCK SET repeatedly until the program number you want to edit appears. 2 Press 4 or . to select a new track number, then press PROGRAM/CLOCK SET. Erasing the entire program in the memory Press PROGRAM/CLOCK SET so that the PROG indicator blinks, and press STOP 7 while the PROG indicator blinks. The stored program is also cleared when the CD door is opened. Note: You can program up to 20 tracks in any desired order.The 21st program will overwrite the program number “01”. INTRO PLAYBACK Every track or every programmed track of a CD can be played for the beginning ten seconds. Press INTRO on the remote control unit. The INTRO indicator appears in the display window and intro playback starts.To use intro playback for programmed and random playback, press the button after starting playback. To quit intro playback, press INTRO again. CARE AND MAINTENANCE CLEANING THE EXTERIOR • Disconnect the system from AC power before cleaning the exterior of the unit with a soft dry cloth. HANDLING DISCS • Remove the disc from its case by holding it at the edge while pressing the center hole lightly. • Do not touch the shiny surface of the disc, or bend the disc. • Put the disc back in its case after use to prevent warping. • Be careful not to scratch the surface of the disc when placing it back in its case. •Avoid exposure to direct sunlight, temperature extremes, and moisture. To clean the disc • Wipe the disc with a soft cloth in a straight line from center to edge. • DO NOT use any solvent-such as conventional record cleaner, spray, thinner, or benzine-to clean the disc. HANDLING CASSETTE TAPES • If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating. • If the tape is loose, it may get stretched, cut, or caught in the cassette. • Be careful not to touch the tape surface. •Avoid storing tapes in any of the following places: -In dusty places -In direct sunlight or heat -In moist areas -On a TV or speaker -Near a magnet CLEANING THE TAPE HEADS Clean the heads after every 10 hours of use with a wet-type head cleaning tape (available at electronic and audio shops). Pinch roller Capstan Head Erasure head To demagnetize the head Turn off the unit, and use a head demagnetizer (available at electronic and audio shops). TROUBLESHOOTING TIPS Problem Solution System does not turn on. • Make sure the power cord is securely plugged into the AC power outlet (or that the batteries are fresh). • Unplug the unit for a moment, and then plug it back in again. • Check the outlet by plugging in another device. No sound • Adjust the volume setting. • Make sure you have selected the correct function: CD, TAPE, or TUNER and the headphones are disconnected. Poor radio reception • Adjust the FM telescopic antenna for better FM reception. • Rotate the unit to achieve better AM reception. •Try turning off electrical appliances near the unit, such as TV, hair dryers, vacuum cleaners, or fluorrescent lights. CD does not play. • Make sure the tray contains a CD. • Make sure the CD’s label is facing up. • Make sure that pause mode is not activated. • Make sure the CD function is selected. CD sound skips. • Clean the CD (as explained in “CARE AND MAINTENANCE”). • Check the CD for warping, scratches, or other damage. • Check for vibration or shock that may affect the unit; move system if necessary. Distorted or noisy recordings • Inspect the recording head and clean it if necessary. • Demagnetize recording head (as explained in “CARE AND MAINTENANCE”). Resetting the unit If “TROUBLESHOOTING TIPS” does not eliminate malfunctioning (failure to operate or display properly, etc.), press the RESET button on the rear of the unit with something having a sharp point, while the unit is turned on. Sharp point Note: Resetting causes the unit to restore its factory default settings and results in all the settings made by the user being deleted. SPECIFICATIONS CD pla...