Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Some stove owners lightly spray an anti-creosote chemical on the fire to help reduce creosote formation within the stove. FIGURE 26 FIGURE 25 . . Air Switch Tube Air Switch Tube REAR VIEW – P24FS FIGURE 27a CONTROL BOARD CONVECTION BLOWER AIR SWITCH AUGER MOTOR AUGER SHAFT COMB. BLOWER SIDE CUTAWAY – P24FS FIGURE 27b 22 MAINTENANCE FIGURE 28a FIGURE 28b COMB. BLOWER AUGER MOTOR AIR SWITCH CONTROL BOARD CONV. BLOWER HIGH TEMP THERMODISK COMB. BLOWER POF THERMODISK PELLET HOPPER AUGER SHAFT CHIMNEY CLEANING a. Creosote Formation – When any wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue or a newly started fire or from a slow- burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire, which may damage the chimney or even destroy the house. Despite their high efficiency, pellet stoves can accumulate creosote under certain conditions. b. Fly Ash – This accumulates in the horizontal portion of an exhaust run. Though noncombustible, it may impede the normal exhaust flow. It should therefore be periodically removed. c. Inspection and Removal – The chimney connector and chimney should be inspected annually or per ton to determine if a creosote or fly ash build-up has occurred. If creosote has accumulated, it should be removed to reduce the risk of a chimney fire. Inspect the system at the stove connection and at the chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as from the bottom. The creosote should be removed with a brush specifically designed for the type of chimney in use. A qualified chimney sweep can perform this service. It is also recommended that before each heating season the entire system be professionally inspected, cleaned and, if necessary, repaired. To clean the chimney, detach the vent at the combustion blower transition where it is attached to the blower. (See Fig. 29 for the P24 Insert) RECOMMENDED MAINTENANCE SCHEDULE Use this as a guide under average-use conditions. Daily Weekly Annually or per Ton Burn Pot Stirred Emptied Glass Wiped Cleaned Combustion Chamber Brushed Ashes Emptied Interior Chambers Vacuumed Heat Exchange Tubes Two passes Combustion Blower Blades Vacuumed / Brushed Convection Blower Impeller Vacuumed / Brushed Vent System Cleaned Gaskets Inspected Hopper (end of season) Emptied and vacuumed Gasket around door and door glass should be inspected and repaired or replaced when necessary (see “REPLACEMENT PARTS”). REMOVAL AND REPLACEMENT OF BROKEN DOOR GLASS While wearing leather gloves (or any other gloves suitable for handling broken glass), carefully remove any loose pieces of glass from the doorframe. Dispose of all broken glass properly. Return the damaged door to your Breckwell Dealer for repair or replacement. Neither the appliance owner nor any other unauthorized person(s) should replace the door glass. An authorized Breckwell dealer must perform all repairs involving door glass. MAINTENANCE 23 MAINTENANCE 23 FIGURE 29 TROUBLESHOOTING GUIDE24 TROUBLESHOOTING GUIDE24 When your stove acts out of the ordinary, the first reaction is to call for help. This guide may save time and money by enabling you to solve simple problems yourself. Problems can be caused by to only five factors: 1) poor fuel; 2) poor operation or maintenance; 3) poor installation; 4) component failure; 5) factory defect. You can usually solve those problems related to 1 and 2. Your dealer can solve problems relating to 3, 4 and 5. Refer to figures 27 - 30 to help locate indicated parts. STOVE SHUTS OFF AND THE # 2 LIGHT FLASHES Possible Causes: Possible Remedies: (Unplug stove first when possible) 1. Airflow switch hose or stove attachment pipes for hose are blocked. Unhook air hose from the air switch and blow through it. If air flows freely, the hose and tube are fine. If air will not flow throw the hose, use a wire coat hanger to clear the blockage. 2. The air inlet, burnpot, interior combustion air chambers, combustion blower, or exhaust pipe are blocked with ash or foreign material. Follow all cleaning procedures in the maintenance section of the owner’s manual. 3. The firebox is not properly sealed. Make sure the door is closed and that the gasket is in good shape. If the ash door has a latch, make sure the ash door is properly latched and the gasket is sealing good. If the stove has just a small hole for the ashes to fall through under the burnpot, make sure the slider plate is in place to seal off the firebox floor. 4. Vent pipe is incorrectly installed. Check to make sure vent pipe installation meets criteria in owner’s manual. 5. The airflow switch wire connections are bad. Check the connectors that attach the gray wires to the air switch. 6. The gray wires are pulled loose at the Molex connector on the wiring...
Otros modelos de este manual:Placa - P24I (744.59 kb)