Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
12. 120°F (49°C)-N/C TEMPERATURE SENSOR (IGNITER SHUT DOWN SENSOR) This sensor (mounted on the exhaust channel) will turn the igniter off when the exhaust channel temperature reaches 120°F (49°C). 13. IGNITER Is a heating element used to ignite the fuel? When the start up switch is activated, the igniter is has power going to the igniter when the switch is in the manual position. Air passes through the igniter tube, which becomes super heated drying the fuel and then igniting the fuel through convection. 14. VACUUM SWITCH This safety device (mounted on the left side pillar) detects vacuum in the exhaust system. If the exhaust blower fails or the vent pipe becomes plugged, this switch will sense that there is no airflow and will stop the auger from continuing to feed pellets. Oval: 5 Oval: 6 Oval: 7 Oval: 8 Oval: 9 Oval: 10 Oval: 11 Oval: 12 Oval: 14 DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE 1. Check clearances to combustibles. 2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be obtained from a ventilated crawlspace. 3. Do not install the stove in a bedroom. 4. You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry or metal chimney (must be lined if the chimney is over 6” in diameter, or less than 28 sq. inches cross sectional area). An interior vent can be used with approved pipe passing through the ceiling and roof. 5. Locate the stove in a large and open room that is centrally located in the house. This will optimize heat circulation. 6. The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach the nearest electrical outlet. VENT TERMINATION REQUIREMENTS A) Do not terminate the vent in any enclosed or semi-enclosed areas, such as a carport, garage, attic, crawl space, narrow walkway, closely fenced area, under a sundeck or porch, or any location that can build up a concentration of fumes such as stairwells, covered breezeway, etc. B) Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shielding r guards may be required. C) Termination must exhaust above inlet elevation. It is recommended that at least five feet of vertical pipe be installed when the appliance is vented directly through a wall to create some natural draft. This is to prevent the possibility of smoke or odor during appliance shut down and to keep exhaust from causing a nuisance or hazard from exposing people or shrubs to high temperatures. In any case, the safest and preferred venting method is to extend the vent through the roof. D) The vent terminal cannot be: -Less than 4 feet (1.2 m) below -Less than 4 feet (1.2 m) horizontally from, and -Less than 1 foot (30 cm) above doors, window openings, or gravity /ventilation air inlets into the building. E) Distance from bottom termination and grade –12” (305 mm) minimum. This is conditional upon the plants and nature of grade surface. The exhaust gases are hot enough to ignite grass, plants and shrubs that are located in the vicinity of termination. The grade surface must not be lawn. Distance from bottom of termination and public walkways is 7 feet (2.1 m) minimum. F) Distance to combustible materials is 2 feet (610 mm). This includes adjacent buildings, fences, protruding arts of the structure, roof overhang, plants, shrubs, etc. G) When installing an FPI or BIH the chimney must be fully lined. Unless the chimneys inside diameter are less than 6” around or has a cross section area of less than 28 square inches. We strongly recommend lining all masonry chimneys H) If the unit is incorrectly vented or the air to fuel mixture is out of balance, a slight discoloration of the exterior of the house might occur. Since these factors are beyond Sherwood Industries Ltd. Control, we grant no guarantee against such incidents. IT IS RECOMMENDED THAT ONLY AN AUTHORIZED DEALER INSTALL YOUR PELLET STOVE REMOVING YOUR NEW STOVE FROM IT’S PALLET To remove your new stove from its pallet, open the left and right side panels. There are two wood screws that are holding the bottom of the stove to the pallet. Remove the screws. Close the side panels. See PAGE 18 how to install the pedestal. INSERT MODEL FREESTAND MODEL DIMENSIONS Text Box: REMOVE SCREW HERE Text Box: 30.5” Text Box: 24” Text Box: 22” Text Box: 11 .” Text Box: SURROUND PANEL MASONRY FIREPLACE INSERT INSTALLATION, MODEL FPI The Fireplace insert model includes a surround faceplate and a pedestal. When installing this unit, ensure that the pedestal is removed from the inside of the hopper and installed on the bottom of the unit. (Surround assembly instructions are in this manual) CLEARANCES TO COMBUSTIBLES Side wall 8” (200 mm) from the body of the heater Facing on masonry fireplace 8” (200 mm) from the body of the heater Mantle 8” (200 mm) from the body of the heater FIREPLACE INSERT SIZE: Width 22”(550 mm) Height 22 3/4(570 mm) Depth 24”(600 mm) A noncombustible hearth pad must cov...