Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Selecting options/ standard settings Operating principle Remote Options ** The dishwasher installs itself automatically during the first use within a serve@Home network. In some cases however, it might become necessary to start the enrolment process anew. If the option “Remote Options” is selected, the message “Enrol Device” will be displayed. By pressing the button + 3 you enrol the device again at the gateway. After successfully enrolling the device the message “Auto Wash” will be displayed. If the enrolment is unsuccessful the display shows “no gateway found”. ** Only with installed interface From the Main Menu you can select the following options/settings by repeatedly pressing the button M/OK 2 : Timer programming Remote Control** Reduce Time Drying Level Buzzer Volume Adding Rinse Aid Water Hardness Language Standard Programmes Remote Setting** ** Only with installed interface Within an option/basic setting there are several possible settings that can be selected using the buttons – or + 3 . A selected setting is applied by changing to the next option/basic setting using the button M/OK 2 . If a setting has been changed using the buttons – or + and stored using M/OK 2 , the message “Value Stored” will be displayed and the display returns to the Main Menu. Timer programming You can delay the programme start by 24 hours in steps of minutes. If the option “Time Pre-select” is chosen the display shows “Delay start: 00 mins”. Set the desired time. Return to the Main Menu by pressing M/OK 2 and start the required programme by pressing the Start Button 4 . Close the door. This starts the time counting backwards. When the set time has elapsed the programme will start automatically. Until the programme starts you are able to change the set time and programme. To do this, use the button – 3 to return to the Main Menu and change the settings. Then start the programme again. In order to delete the pre-selected time, set the time back to “Delay start: 00 mins”. Remote Control** After choosing the option “Remote Control” the display will show “Remote Control: Off” (factory setting) You activate this option by selecting “Remote Control: On”. ** Only with installed serve@Home interface Reduce Time (VarioSpeed) The Auto Programmes allow you to reduce the run time of the programmes. However, in order to achieve an optimal cleaning result, the water and energy consumption will be increased. If the option “Reduce time” is chosen the display shows “Reduce time: Off” (factory setting). Select “Reduce time: On”. Return to the Main Menu by pressing M/OK 2 and start the required programme by pressing the Start Button 4 . en If you do not want to use “Reduce time” the next time you use the dishwasher, you must deselect this option. Drying Level If the option “Drying Level” is chosen the display shows “Normal drying” (factory setting). Alternatively you can select “Eco drying” or “Extra drying”. The option ”Extra drying” increases the temperature during rinsing in all programmes. (Please take care with delicate dishes.) Buzzer Volume You can vary or even completely switch off the volume of the acoustic end-of-programme signal. If the option “Buzzer Volume” is chosen the display shows “Buzzer 6” (factory setting). You can change this value to 0 (acoustic signals switched off) or to values between 1 (quiet) and 6 (loud). A short buzz demonstrates the currently chosen volume level. Adding Rinse Aid You can set the amount of rinse aid added. If the option “Adding Rinse Aid” is chosen the display shows “Rinse Aid 4” (factory setting). Change this setting only if there are streaks (reduce the value) or water stains (increase the value) remaining on the dishes. You can choose a value between 0 and 6. Water Hardness Before starting the appliance for the first time or in case of changes in the water hardness, the dishwasher’s softening system must be set to the hardness of your mains water supply. Follow the instructions set out in the chapter “Set-up of the Softening System”. en Language You can change the language selected when the appliance was started for the first time (see chapter “Before Starting The Device For The First Time”). If the option “Language” is chosen the display shows several language abbreviations. The abbreviation of the currently selected language is flashing. In order to choose a different language, press – or + 3 until the desired language appears. Confirm the language selection by pressing M/OK 2 . All following optical character messages will be displayed in the selected language. Standard Programmes In addition to the rinse programmes available in the Main Menu you can choose among the following standard programmes from the programme “Normal”: Extra, Eco 50, Eco 45, Normal 45. Set the desired programme and start the selected programme by pressing the Start Button 4 . If you do not want to use any of the displayed standard programmes return to the Main Menu by using the button M/OK 2 . If you want to cancel t...