Votos - , Puntuación media: ( )

Manual de usuario Fisher & Paykel, modelo 685000800012

Fabricar: Fisher & Paykel
Tamaño del archivo: 427.04 kb
Nombre del archivo: 685000800012.pdf

Idioma del manual:

El documento se está cargando, por favor, espere

Descargar ahoraCerca

El documento se está cargando, por favor, espere

Descargar ahoraCerca

This guide will help you anticipate drain, water, and electrical connections, and help you select the best location for the dishwasher. Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Failure to follow this warning can result in serious injury. Installation Tips 1 Tools and Materials Needed for Installation (Not Included) • Drill, Electric • Driver, Socket 5/32”, 1/4” , 5/16” • Flaring Tool / Tube Cutter (for copper tubing) • Flashlight • Level • Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads) • Pliers • Safety Glasses • Saw, Keyhole or 1/2”, 11/2” to 2” Hole Cutters • Screw Drivers, Slotted and #2 Phillips (magnetic tip preferred) • Tape, Electrical or Duct • Tape, Measuring • Wire Stripper or Utility Knife • Wrench, Hex-end • Wrenches, 2 Adjustable (for copper tubing) or 2 Pipe wrenches (for iron pipe plumbing) Parts You Will Need* (Not Included) • Brass Elbow, 90° with a 3/8” National Pipe Thread • Conduit Connector (UL Listed) • Wire Nuts, three (3) for 12-14 gauge wire (UL Listed) * If required: • “Y” Branch Tailpiece and Connector Kit (See Step 4) • Air Gap Kit (See Step 4) All the parts can be found at local hardware, electrical and plumbing supply stores. Electric Shock Hazard Electrical, water, and drain lines must be confined to shaded areas in Figure 2. Electric conductors, water, and drain could be damaged. Failure to follow these instructions could result in fire or electric shock. NOTE: If dishwasher is installed at end of a cabinet, sides and back must be fully enclosed. Connections For Electrical, 4 Water, and Drain Locating the Connections 1. Review dimensions in Figure 2 to locate dishwasher’s drain, water, and electrical connections. 2. All utilities must be routed in shaded area in the Figure 2. IMPORTANT: Disconnect power before starting installation. Note: Locate the electrical supply and dishwasher’s electrical 4. Locate water inlet valve behind kickplate on bottom left underside of unit.See Figure 4. The valve has a 3/8” NPT female fitting. 5. Wrap 90° elbow (not included) with pipe thread tape (or apply joint compound) and thread it into water inlet valve. When tightened, elbow should point toward the left. To prevent bending of bracket or breaking of valve, avoid overtightening. See Figure 4. NOTE: Put unit on its back being careful not to pinch the Water Drain Hose. 1. Remove two (2) screws at front of the kickplate using a #2 Phillips screw driver. 2. Tilt and pull forward to remove see figure 1a. NOTE: It is not necessary to remove the outer door for installation. Installation Preparation 2 junction box on right underside of unit behind kickplate assembly. See Figure 4. Determine where you will connect to hot water supply. Review Figure 4 and note the location of water inlet valve. Determine where you will connect the drain hose. 3. Cut access holes for the Electrical, Water and Drain hoses in the shaded areas as shown in Figure 2. 4. The dishwasher operates on a 120 volt, 60 Hz electrical supply. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps. 5. Pu...