All units are individually calibrated and tested in CO gas in order to ensure accuracy. In addition, the sensor module can be easily changed for a new module at the end of its 5 year life. The Ei206D also has a built-in digital display which shows the CO level sensed in parts-per-million (ppm). The Ei206D is housed in a slimline casing and can be easily secured to a wall or ceiling, with a separate base- plate and all necessary fixings supplied. As well as being easy to install and maintain, the alarm also has a vitally important memory feature which records if CO has been detected whilst the occupier was away. An easy to use Test/Hush button allows the user to check that the horn and electronics are working and to silence nuisance alarms. The green indicator will flash every minute to indicate that the battery supply is healthy. If CO is detected, the horn will sound and the digital display will indicate the level of CO sensed in parts-permillion (ppm). The red indicator will also flash. The horn will beep and the digital display will show „SF. in the event of a sensor fault. The amber indicator will also flash every minute. The horn will beep and the green indicator will flash every minute to indicate that the batteries are depleted. Memory Feature -when the test button is pressed the horn will sound and the digital display will indicate the level of CO previously detected in ppm. The “Test/Hush” button will either silence false alarms (if briefly pressed) or perform a unit self test (if pressed and held). Note that the alarm cannot be silenced when sensing a CO level of 300ppm or above. Shannon Free Zone, Shannon, Co. Clare, Ireland. Ph.+353 61 471277 Fx.+353 61 471053 Email. eielectronics@eiltd.ie Web: E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei206D DataSht RevB Model Ei206D Model Ei206D Technical Specification 1. The CO Alarm carries the BSI Kitemark to indicate type testing to BS EN 50291:2001. It is CE marked to indicate conformance to BS EN 60065: 1994, BS EN 50081-1: 1992 and BS EN 50270: 1992 Safety and Electromagnetic Compatibility Directives. 2. New generation electrochemical cell type Carbon Monoxide sensor checks CO concentration every 50 seconds. Each unit is calibrated and tested in CO gas in order to ensure accuracy. Sensor module plugs into base of unit and should be replaced after 5 years. The amber „Fault. light will flash once every 40 seconds (without a beep) to indicate the sensor should be replaced. Replacement sensor modules, Ei261MEN, are readily available at modest cost. Does not require an electrician to change the sensor. 3. High level of selectivity. No false alarms when exposed to the following interference gases for 2 hours: (as per UL2034sec.38) Methane 500ppm, Butane 300ppm, Heptane 500ppm, Ethyl Acetate 200ppm, Isopropyl Alcohol 200ppm and Carbon Dioxide 1000ppm. 4. Digital display will indicate the level of CO sensed when the unit is in alarm in parts-per-million (ppm). 5. Alarm response time varies with CO level sensed: at 50ppm CO sounder operates within 60-90 mins; at 100ppm CO sounder operates within 10-40 mins; at 350ppm CO sounder operates within 3 minutes. 6. Battery powered -supplied with 9V Alkaline PP3 battery. The green LED on the cover will flash every 50 seconds to indicate battery power is present. The alarm will emit a single beep every 50 seconds (with the green LED flash) to indicate the battery needs replacement. 7. On first power up the green, red and amber LED.s flash once; after 2 minutes settling, the unit operates normally. 8. Fault indicator -amber LED flashes and horn beeps every 50 seconds if a fault is detected. If sensor fault, digital display will show „SF.. 9. Supplied with separate base-plate and fixing screws: suitable for ceiling or wall mounting. 10. Tamper resistant cover, which cannot be removed from mounting plate without releasing catch with a small screwdriver. An optional locking screw can be screwed into the side to prevent removal. 11. Manual test/hush button -test button to test circuitry and horn. Pressing and releasing the test button when the unit is sensing CO will silence the alarm for 4 minutes. It will only silence once until the gas clears. At 300ppm CO the unit cannot be silenced due to the increased danger. 12. Quick CO gas test -allows quick and easy testing of the unit with CO gas. Pressing the test button causes the sensor to test for CO every 4 seconds. The unit automatically resets after approximately 3 minutes. 13. Memory feature -pressing test button shows if CO has been detected during a period of absence: the unit will alarm and the digital display will show the level of CO previously sensed. Pressing the test button for 20 seconds resets the memory. 14. Built in sounder to give a minimum output of 85dB(A) at 3 metres. Modulated sound output -3 rapid pulses followed by a 1. second pause, repeated unti...