This warranty extends only to the sale of new and unused products to the original buyer. BWs warranty obligation is limited, at BWs option, to refund of the purchase price, repair or replacement of a defective product that is returned to a BW authorized service center within the warranty period. In no event shall BWs liability hereunder exceed the purchase price actually paid by the buyer for the Product. This warranty does not include: a) fuses, disposable batteries or the routine replacement

The photocell is a ceramic disk coated with cadmium sulfide and overlaid with a conductive grid. Electrodes attached to the ceramic disk transmit an electrical signal to the primary control. In darkness, cadmium sulfide has a very high resistance to the passage of electrical current. In visible light, its resistance is very low and current is allowed to pass. The entire cell is hermetically sealed (glass to metal) to prevent cell deterioration. M7854 PLUG-IN-CELL MOUNTING BRACKET SOCKET LEADWIRE

Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until manuals are read and understood. CAUTION - System Re-acceptance Test after Software Changes: To ensure proper system operation, this product must be tested in accordance with NFPA 72 after any programming operation or change in site-s

3 Installation ......................................................................... 3 Wiring ................................................................................. 4 XL800 Series Power Consumption ................................ 5 I/O Modules ................................................................... 5 Description of the XCL8010AU Controller Module ......... 7 Overview........................................................................ 7 Interfaces and Bus Connectio

Installation Instructions for use with HyperTerminal™ and serial port Parts List Part Numbers Description IPDACT Internet Communicator-Contact ID only. Requires compatible FL panel equipped with on-board or optional DACT. Requires 300mA aux non-reset able power from FACP. Includes cable from panel primary telco port to IPDACT. IPBRKT Bracket for mounting IPDACT inside MS- 9200UDLS common enclosure or in optional HPP-300ULX power supply IPSPLT Splitter for dual phone lines to IPDACT input cable.

EXTERNAL CONNECTIONS.................................................................................3 3. POWER SUPPLY...................................................................................................4 4. ANALOGUE OUTPUTS.........................................................................................4 5. RELAY CONTACTS...............................................................................................5 6. GAS DETECTION RANGE...................................

During this period we will, at our discretion, repair, replace of refund the price of any part of the gas alarm which is found to be defective in either materials or workmanship providing this occurs under normal use and service. We shall, however, be under noobligation to repair, replace or refund the price of units which are found to be defective in any way due to damage, neglect, unreasonable use or which have been tampered with or found to have been dismantled. Defective units should be retu

Contact authorized service personnel immediately. See below. Manual activation (Fire Drill or otherwise) Notification Appliance Circuits (NACs) can be activated by pressing and holding the DRILL button for at least two seconds. NOTE: You may want to disconnect the municipal box by sliding the DISCONNECT switch, located on the 4XTMF module, to its disconnect position (to the right). If a DACT is connected, notify the monitoring service before conducting any fire drills or tests. Alarm Silenc

All Rights Reserved. 1 Introduction Warning To ensure your personal safety, read “Safety Information” (below) before you use the controller. The AirAlertTM96d system sets new standards in gas detection and in the measurement of environmental parameters. Acting as the nerve center of a modular gas detection network, the AirAlertTM96d provides continuous monitoring of up to 96 connected units on three distinct channels. The AirAlertTM96d provides a full array of displays. At a glance, it is possib

LCD display will read SYSTEM following location: ALL NORMAL. WHEN AUDIBLE DEVICES ARE SOUNDING -FORANALARM 1. Evacuate the protected area 2. Notify the monitoring service and/or the Fire Department immediately. Tell them briefly what happened and what your current status is. Phones:__ Fire Department Monitoring Service 3. If the Fire Department is responding, be prepared to provide directions to arriving firefighters. FOR TROUBLE, SUPERVISORY, AND EMERGENCY ALARMS 1. Notify the monitori