Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
10. 9. 8. 7. 5. 4. 3. 2. 1. 16. 15. 14. 13. 12. 6. 1. Scanner glass 9. USB drive/PictBridge port 2. Printer access door 10. Memory card light 3. Output tray 11. Memory card slots 4. Paper-width guide 12. Control panel 5. Main tray13. USB port 6. Photo tray 14. Power connector 7. Paper-length guide 15. Rear access door8. Photo tray light 16. Scanner lid Unpack Printer and Install Control Panel 1 3 a) See box flaps for unpacking instructions. Remove all orange shipping tape from the printer. c) Press down on all edges of the overlay until it snaps into position. Transfer RotateZoom Attention CancelOn/Off HelpMenu Scan Copy Photo Proofsheet EasyShare 5300 All-in-One Printer OK b) If not preinstalled, insert the control panel overlay, bottom end first. EasyShare 5300E All-in-One Printer OK OK IMPORTANT: Do not connect the USB cable to the printer until instructed during software installation. 4 Load Paper 2 b) Push the photo tray in until it clicks into place. NOTE: You can only print to the photo tray when the photo tray is pushed in. Lower the photo tray lid. a) Load photo paper into the photo tray. Lift the photo tray lid until it remains standing without support. Insert the photo paper glossy side down. IMPORTANT: Do not overload the photo tray. Max 20 sheets. c) Load plain white paper into the main tray. 3 Install Printhead IMPORTANT: The printhead is fragile. Handle carefully. a) Lift the printer access door. Make sure the orange tape is removed from the carriage. b) Remove the printhead from its bag. IMPORTANT: Insert the printhead immediately upon opening sealed bag. c) Pull on the orange tab to remove the protective retainer. Install Printhead d) Carefully remove and discard the black plastic shield and the orange protective cap. IMPORTANT: Do not touch the copper-colored contacts. e) Place the printhead into the carriage. Insert at the angle shown. f) Push firmly against the back wall of the printhead until it clicks into place. Tip: The printhead requires a firm push and makes an audible click when locked into place. 4 4 Install Ink Cartridges 10Black Ink Car ridg a) Remove the black ink cartridge from its bag. IMPORTANT: Insert ink cartridges immediately upon opening sealed bag. 10Black Ink Car b) Carefully remove and discard the orange cap. Handle ink cartridges carefully to avoid ink transfer. 10Black Ink C tridg c) Insert the black ink cartridge into the printhead. Install Ink Cartridges 10Black Ink Cartridge 10 d) Press down on the ink cartridge until you hear it click into position. 10Black Ink Cartridge 10 C o lor In k C ar tr idge e) Open and uncap the color ink cartridge. Insert it into the printhead. 10Black Ink Cartridge olor Ink Cartridge 10 f) Press down firmly on the ink cartridge until you hear it click into position. It is normal for the printhead to flex when inserting the cartridge. You will not damage the printer. Close the printer access door. 55 Connect Power Easyshare 5300 All-in-One Printer a) Connect the power supply and adapter. All-in-One Printer EasyShare 5300 b) Remove the plastic film from the LCD display. Position the LCD display and press ON. All-in-One Pr r EasyShare 5300 -ON c) Press ON. If prompted, select your language. Use the key to select a region. 6 6 Calibrate Printer IMPORTANT: Make sure that the photo tray is pushed in. The photo tray light should be lit. a) Press Start. Wait two minutes for the calibration sheet to print. Tip: If the calibration sheet does not print properly, see the Troubleshooting section in this setup guide. 4x6 b) Remove the calibration sheet from the output tray. Place it face down and align to the front, right corner of the scanner glass, as shown. IMPORTANT: The blue arrow in the corner of the calibration sheet must point to the registration marks as shown. 4x64x6 c) Lower the scanner lid and press Start. Remove the sheet from the scanner glass when the calibration is complete. d) Lift the photo tray lid, then slide the photo tray toward you to return to main tray operation. The photo tray light will turn off. 7 7 Install Software WINDOWS WINDOW WINDOWS WINDO WINDOWS WINDO WINDOWS WINDO WINDOWS WINDO WINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDO WINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS IMPORTANT: Do not connect the USB cable to the printer until instructed during software installation. a) Load the Kodak AiO Printer Software CD into the CD-ROM drive. Follow the on-screen prompts when the instructions appear. If instructions do not appear, click Start, then Run. Select CD-ROM drive and type setup.exe, then press ENTER. b) Connect the USB cable to the printer when instructed. Continue to follow the on-screen prompts until installation is complete. b) Load the Kodak AiO Printer Sof...