Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Apply some mechanical assistance in below procedures to help resetting the cutter blade back to its home position. Please lift up a transparent protective cover over the adjustment wheel with the printer powered off. Turn this wheel downward for 4 or 5 strokes. Close the cutter cover back and turn the printer power on to see if the auto cutter lock up problem is resolved. If the problem is not automatically resolved by above procedures, please power off the printer and open the cutter cover again. Check in the alignment window while turning the gear downward as above or with a small Phillips screwdriver at the right side of the cutter mechanism. When the cutter blade returns to its standard position, a hole in the white plastic gear will show up in the window as illustrated in detailed picture above. Close the cutter cover Auto Cutter Track Thermal Elements Open Cutter Cover when hood locked Lift transparent protective foil Alignment window Adjustment area detailed below Use screwdriver Turn the adjustment wheel downward for few strokes when finish. The lock up of the print hood can then be released after this problem solved. Please use manual cutter as temporary alternative measure once the auto cutter malfunctioned. Advanced Analysis Tool This printer supports Hexadecimal Dump for experienced user to view exactly what data is received by the printer. This can be useful in finding software problems. To start the dump mode: Turn off printer; Open print hood; Hold down FEED button while turning printer on; Close the hood. To stop the dump mode: Press the FEED button to print out the last line; Turn off the printer. During dump mode: All commands except DLE EOT and DLE ENQ are disabled. USEFUL TIPS .. Please note that only those qualified technicians may adjust several jumpers for some technical settings. Please visit our web site or for details of the technical information such as driver installation, DIP switch settings and command sets etc. if required. .. Place the printer on a sturdy, level surface. .. Choose a place that is well ventilated and free of excessive dust, smoke or fume. .. Do not put the printer under direct sunlight or near a heater. .. Ideal room temperature is from 5.C to 40.C. Ideal humidity is from 20% to 85% RH (no condensation). .. Do not set any liquid or drinks such as coffee on the printer case. .. Do not touch any metal part to avoid possible electrostatic damage. .. Do not touch the areas around the print head and motor during or right after printing. It can be very hot. .. Do not allow the cut receipt to slide back into the cutter during the operation. As this would lead to multiple cutting at the lower edge of a receipt and the multiple cut thin slips tend to cause mechanical malfunction. .. Use a grounded AC power outlet with only the power cord and power adaptor furnished with the printer. .. Do not use a power outlet of a circuit shared with any equipment that uses Part 14 a lot of power or causes great electrical noises, such as a copier, electric motors or a coffee maker. .. Do not use thermal paper containing Sodium (Na+), Potassium (K+) and Chlorine (Cl-) ions that can harm the print head thermal elements. .. If the surface of thermal paper is scratched with a hard object such as a nail, the paper may become discolored. .. If thermal paper touches diazzo copy paper immediately after copying, the printed surface may be discolored. .. Use only water paste, starch paste, polyvinyl paste or CMC paste when gluing thermal paper. .. If thermal paper touches anything containing phthalic acid ester plasticizer for a long time, the image formation ability may be reduced or the printed image may fade. .. Use of volatile organic solvents such as alcohol, ester and ketone or some adhesive tapes on thermal paper can cause discoloration. .. Thermal paper must not be stored with the printed surfaces against each other as the printing may be transferred between the surfaces. .. Since the paper roll is highly thermal sensitive, please keep them in a dark place that is 20. and 65% RH when not installed in the printer. Avoid extended exposure to direct light. Use only products made from polyethylene, polypropylene or polyester for storage of thermal paper. Part 15 SPECIFICATIONS PRINTER ITEM SPECIFICATION Printing method Thermal sensitive line dot method Effective printing width 64 mm Thermal head configuration 512 dots / line Printing speed 220 mm / sec. max. Paper feed method Friction auto-feed Paper load method Drop and use Auto-cutter capability Partial cut (1 point at center left) Manual cutter Saw tooth blade Dot Pitch 0.125 x 0.125 mm Input power type DC Input voltage 24 V + / - 5 % Dimension (mm) 148 (W) x 205 (D) x 143 (H) Weight 1.2 Kg net PAPER PAPER TYPE THERMAL ROLL PAPER Paper roll formation External side is heat-sensitive side Paper width 80 (or 58) + 0 / - 1 mm Paper roll outer diameter 83 mm max. Paper roll inner diameter 1...
Otros modelos de este manual:Impresoras - AURA PP-8000 (798.57 kb)
Impresoras - AURA PP-8000L (798.57 kb)