Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
2 1 2 3 Media and tray 2. Learning the Basic Usage 29 5 Place the paper with the side you want to print facing up. For paper smaller than Letter-sized, press and unlatch the guide lock in the tray, push the tray in manually. Then adjust the paper length guide and paper width guide. For paper longer than Legal-sized, press and unlatch the guide lock in the tray, pull the tray out manually. Then adjust the paper length guide and paper width guide. • Do not push the paper width guide too far causing the media to warp. • Do not use a paper with a leading-edge curl, it may cause a paper jam or the paper can be wrinkled. • If you do not adjust the paper width guide, it may cause paper jams. 2 1 2 1 Media and tray 2. Learning the Basic Usage 30 6 Squeeze the paper width guide and slide it to the edge of the paper stack without causing it to bend. 7 Close the paper cover. 8 Insert the paper tray. 9 When you print a document, set the paper type and size for the tray (see "Setting the paper size and type" on page 33). The settings made from the machine driver override the settings on the control panel. a To print in application, open an application and start the print menu. b Open Printing Preferences (see "Opening printing preferences" on page 35). c Press the Paper tab in Printing Preferences, and select an appropriate paper type. For example, if you want to use a label, set the paper type to Label. d Select Auto Select (or Manual Feeder) in paper source, then press OK. e Start printing in application. Media and tray Media and tray Printing on special media Types Traya CardStock . Labels . Preprinted . Cotton . Recycled . Archive . Glossy Photo . Matte Photo . The table below shows the special media usable in each tray. The media types are shown in the Printing Preferences. To get the higest printing quality, select the proper media type from the Printing Preferences window > Paper tab > Paper Type (see "Opening printing preferences" on page 35). For example, if you want to print on labels, select Labels for Paper Type. When using special media, we recommend you feed one sheet at a time (see "Print media specifications" on page 70). a. The paper types available manual feeding in tray. (.: Included, Blank: Not available) To see for paper weights for each sheet, refer to "Print media specifications" on page 70. Types Traya Plain . Thick . Thin . Bond . Color . 2. Learning the Basic Usage 31 Media and tray 2. Learning the Basic Usage 32 Labels To avoid damaging the machine, use only labels designed for use in laser printers. • When selecting labels, consider the following factors: - Adhesives: Should be stable at your machine’s fusing temperature. Check your machine’s specifications to view the fusing temperature (about 170°C (338°F)). - Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets that have spaces between the labels, causing serious jams. - Curl: Must lie flat with no more than 5 mm of curl in any direction. - Condition: Do not use labels with wrinkles, bubbles, or other indications of separation. • Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components. • Do not run a sheet of labels through the machine more than once. The adhesive backing is designed for only a single pass through the machine. • Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. Card stock/ Custom-sized paper • In the software application, set margins at least 6.4 mm (0.25 inches) away from the edges of the material. Media and tray 2. Learning the Basic Usage 33 Preprinted paper When loading preprinted paper, the printed side should be facing up with an uncurled edge at the front. If you experience problems with paper feeding, turn the paper around. Note that print quality is not guaranteed. • Must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the machine’s fusing temperature for 0.1 second (about 170°C (338°F)). • Preprinted paper ink must be non-flammable and should not adversely affect machine rollers. • Before you load preprinted paper, verify that the ink on the paper is dry. During the fusing process, wet ink can come off preprinted paper, reducing print quality. 4 Setting the paper size and type After loading paper in the paper tray, set the paper size and type. Open the Printing Preferences (see "Opening printing preferences" on page 35) and set the paper size and type in the Paper tab. If you want to use special-sized paper such as billing paper, select Custom in the Paper tab in the Printing Preferences (see "Opening printing preferences" on page 35). Basic printing For special printing features, refer to the Advanced Guide (see "Using advanced print features" on page 52). Printing If you are a Mac or Linux...
Otros modelos de este manual:Impresoras - CLP-360 (11.77 mb)
Impresoras - CLP-363 (11.77 mb)
Impresoras - CLP-364 (11.77 mb)
Impresoras - CLP-365 (11.77 mb)