Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
The machine starts connecting to the wireless network. The LED blinks slowly for up to two minutes until you press the PBC button on the access point (or wireless router). Press the WPS (PBC) button on the access point (or wireless router). 2 a The light blinks fast on the WPS LED. The machine is connecting to the access point (or wireless router). b When the machine is successfully connected to the wireless network, the WPS LED light stays on. Insert the supplied software CD into your CD-ROM drive, and follow the 3 instructions in the window to set up the wireless network. Connecting in PIN mode The network configuration report, including PIN, must be printed (see 1 "Printing a network configuration report" on page 9). In ready mode, Press the (Cancel or Stop/Clear) button for more than five seconds on the control panel. The machine without the (Cancel or Stop/Clear) button: Press the (WPS) button formore than ten seconds on the control panel. You can find your machine’s PIN. Press and hold the (WPS) button on the control panel for more than 2 4 seconds until the status LED stays on. The machine starts connecting to the access point (or wireless router). You need to enter the eight-digit PIN within two minutes on the 3 computer that is connected to the access point (or wireless router). The LED blinks slowly for up to two minutes until you enter the eight- digit PIN. The WPS LED blinks in the order below: a The light blinks fast on the WPS LED. The machine is connecting to the access point (or wireless router). b When the machine is successfully connected to the wireless network, the WPS LED light stays on. Insert the supplied software CD into your CD-ROM drive, and follow the 4 instructions in the window to set up the wireless network. 2. Using a network-connected machine 26 Wireless network setup Re-connecting to a network When the wireless function is off, the machine automatically tries to re-connect to the access point (or wireless router) with the previously used wireless connection settings and address. In the following cases, the machine automatically re-connects to the wireless network: • The machine is turned off and on again. • The access point (or wireless router) is turned off and on again. Canceling the connection process To cancel the wireless network connection when the machine is connecting to the wireless network, press and release the (Cancel or Stop/Clear) or (Power/Wakeup) button on the control panel. You need to wait 2 minutes to re-connect to the wireless network. Disconnecting from a network To disconnect the wireless network connection, press the (WPS) button on the control panel for more than two seconds. • When the Wi-Fi network is in idle mode: The machine is immediately disconnected from the wireless network and the WPS LED turns off. • When the Wi-Fi network is being used: While the machine waits until the current job is finished, the light blinks fast on the WPS LED. Then, the wireless network connection is automatically disconnected and the WPS LED turns off. Using the menu button Some menus may not appear in the display depending on options or models. If so, it is not applicable to your machine Before starting, you will need to know the network name (SSID) of your wireless network and the network key if it is encrypted. This information was set when the access point (or wireless router) was installed. If you do not know about your wireless environment, please ask the person who set up your network. 2. Using a network-connected machine 27 Wireless network setup Wireless network setup After completing the wireless network connection, you need to install a machine driver to print from an application (see "Installing driver over the network" on page 12). Press the (Menu) button on the control panel. 1 Press Network > Wireless > WLAN Settings. 2 Press the OK to select the setup method you want. 3 • Wizard (recommended): In this mode, the setup is automatic. The machine will display a list of available networks from which to choose. After a network is chosen then printer will prompt for the corresponding security key. • Custom: In this mode, users can give or edit manually their own SSID , or choose the security option in detail. Setup using Windows Shortcut to the Wireless Setting program without the CD: If you have installed the printer driver once, you can access the Wireless Setting program without the CD. From the Start menu, select Programs or All Programs > Samsung Printers > your printer driver name > Wireless Setting Program. Access point via USB cable (recommended) Items to prepare • Access point • Network-connected computer • Software CD that was provided with your machine • A machine installed with a wireless network interface • USB cable Creating the infrastructure network Check whether the USB cable is connected to the machine. 1 Turn on your computer, access point, and machine. 2 Insert the supplied software CD into your CD-ROM drive. 3 2. Using a network-connected...
Otros modelos de este manual:Impresoras - CLP-360 (11.77 mb)
Impresoras - CLP-362 (11.77 mb)
Impresoras - CLP-363 (11.77 mb)
Impresoras - CLP-364 (11.77 mb)