Votos - 2, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Just use a one-touch or speed dial number or dial a number manually using the number keypad. [Incompatible] The remote machine does not have the requested feature, such as a delayed transmission. It also occurs if the remote machine does not have enough memory space to complete the operation you are attempting. Reconfirm the remote machine’s features. [Jam 1] or [No Cartridge] The toner cartridge is not installed. Install the toner cartridge. See page 1.8. Line Busy The remote person did not answer or the line is already engaged. Try again after a few minutes. [Line Error] Your machine cannot connect with the remote machine or has lost contact because of a problem with the phone line. Try again. If the problem persists, wait an hour or so for the line to clear and try again. Or, turn the ECM on. See page 4.6. Load Document You have attempted to set up a copy or fax operation with no document loaded. Load a document and try again. [Low Heat Error] There is a problem in the fuser unit. Unplug the power cord and plug it back in. If the problem persists, please contact a service representative. Open Heat Error [Over Heat] [LSU Error] A problem has occurred in the LSU (Laser Scanning Unit). Unplug the power cord and plug it back in. If the problem persists, please call for service. Memory Full The memory is full. Delete unnecessary documents, retransmit after more memory becomes available or split the transmission into more than one operation. 6.6 TROUBLESHOOTING Display Meaning Suggested solutions [No Answer] The remote fax machine has not answered after several redial attempts. Try again. Make sure that the remote machine is operational. NO. Not Assigned The One-touch or speed dial location you tried to use has no number assigned to it. Dial the number manually using the number keypad or assign the number. For storing a number, see page 2.15. [No Paper] Add Paper The paper tray has run out of paper. Load paper in the paper tray. See page 1.9. Operation Not Assigned You are doing in the Add/ Cancel operation, but there is no jobs waiting. Check the display to see if there is any scheduled job. The display should indicate them in Standby mode, for example, Delay Fax. [Paper Jam 0] Open/Close Door Paper has jammed in the feeding area of the paper tray. Clear the jam. See page 6.3. [Paper Jam 1] Open/Close Door • Paper has jammed in the paper exit area. • A paper jam has occurred in the manual feeder or the machine detects non-feeding from the manual feeder. • Clear the jam. See page 6.4. • Clear the jam. See page 6.5. [Paper Jam 2] Check Inside Paper has jammed in the fuser area. Clear the jam. See page 6.3. Power Failure Power has turned off then on and the machine’s memory has not been saved. You need to start again the job which you were trying to do before the power failure. Retry Redial? The machine is waiting for a specified time interval to redial a previously busy station. You can press Enter to immediately redial, or Stop/Clear to cancel the redial operation. [Stop Pressed] The Stop/Clear button is pressed during a copy or fax operation. Try again. [Toner Empty] The toner cartridge has run out. The machine stops printing. Replace with a new toner cartridge. See page 5.7. [Toner Low] The toner cartridge is almost empty. Take out the toner cartridge and gently shake it. By doing this, you can temporarily reestablish printing operations. 6 TROUBLESHOOTING 6.7 Solving Problems The following chart lists some conditions that may occur and the recommended solutions. Follow the suggested solutions until the problem is corrected. If the problem persists, please call for service. Paper Feeding Problems Condition Suggested solutions Paper is jammed during printing. Clear the paper jam. See page 6.3. Paper sticks together. Ensure that there is not too much paper in the paper tray. The paper tray can hold up to 250 sheets of paper, depending on the thickness of your paper. Make sure that you are using the correct type of paper. See “Paper Specifications” on page A.5. Remove paper from the paper tray and flex or fan the paper. Humid conditions may cause some paper to stick together. Multiple sheets of paper do not feed. Different types of paper may be stacked in the paper tray. Load the paper of only one type, size and weight. If multiple sheets have caused a paper jam, clear the paper jam. See page 6.3. Paper does not feed into the machine. Remove any obstructions inside the machine. Paper has not been loaded correctly. Remove paper from the tray and reload it correctly. There is too much paper in the paper tray. Remove excess paper from the tray. The paper is too thick. Use only paper that meets the specifications required by the machine. See “Paper Specifications” on page A.5. The paper keeps jamming. • There is too much paper in the paper tray. Remove excess paper from the tray. • An incorrect type of paper is being used. Use only paper that meets the specifications required by the machine. See “Paper Specificatio...
Otros modelos de este manual:Impresoras - CF-560G (4.34 mb)
Impresoras - CF-560R (4.34 mb)
Impresoras - CF-560RG (4.34 mb)
Impresoras - SCX-5315F (4.34 mb)