Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Shut-Off Valve 4. Coupling (purchased) 8. Packing Nut 6. Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is clear. Turn off shut-off valve on the water pipe. NOTE: Always drain the water line before making the final connection to the inlet of the water valve to prevent possible water valve malfunction. 7. Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown. REAR VIEW 1. Drain Hose (Drain Pump models only) 2. Vent Hose (Drain Pump models only) 3. Water Supply Line 8. Thread the nut onto the coupling on the end of the copper tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten. 123 432 1. Line to ice maker 3. Ferrule (purchased) 2. Nut (purchased) 4. Coupling (purchased) 9. Remove the two screws in the lower access panel and the two screws in the base grille area of the front panel support. Pull forward to remove the lower access panel. NOTE: To prevent rattling, be sure the copper tubing does not touch the cabinet’s side wall or other parts inside the cabinet. FRONT VIEW " " " 1. Water Pan Drain 2. Water Valve " 10. Turn shut-off valve ON. 11. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak. 12. Replace the lower access panel and screws. Connecting the drain Gravity drain system Connect the ice maker drain to your drain in accordance with all state and local codes and ordinances. If the ice maker is provided with a gravity drain system, follow these guidelines when installing drain lines. This will prevent water from flowing back into the ice maker storage bin and potentially flowing onto the floor causing water damage. ¦ Drain lines must have a minimum of ... in. (15.88 mm) inside diameter. ¦ Drain lines must have a 1 in. drop per 48 in. (2.54 cm drop per 122 cm) of run or ... in. drop per 12 in. (6.35 mm per 30.48 cm) and must not have low points where water can settle. ¦ The floor drains must be large enough to accommodate drainage from all drains. ¦ The ideal installation has a standpipe with a 1... in. (3.81 cm) to 2 in. (5.08 cm) PVC drain reducer installed directly below the outlet of the drain tube as shown. You must maintain a 1 in. (2.54 cm) air gap between the drain pump hose and the standpipe. ¦ It may be desirable to insulate the drain line thoroughly up to the drain inlet. After ensuring that the drain system is adequate, follow these steps to properly place the ice maker: 1. Plug in ice maker or reconnect power. 2. Re-check the ice maker to be sure that it is level. See the “Leveling” section. 3. Push the ice maker into position so that the ice maker drain tube is positioned over the PVC drain reducer. SIDE VIEW 3 5/8" (9.2 cm) 23" (58.4 cm) 1" (2.5 cm) 2" - 1 1/2" (5 cm - 3.8 cm) 1. Drain Hose 2. 1 in. (2.54 cm) Air Gap 3. PVC Drain Reducer 4. Center of drain should be 23 in. (58.4 cm) from front of door (with or without the ... in. (1.91 cm) panel on the door). 4. If it is required by your local sanitation code, seal the cabinet to the floor with an approved caulking compound after all water and electrical connections have been made. Drain pump system (on some models) Connect the drain pump hose (provided with the product) to your drain in accordance with all state and local codes and ordinances. NOTE: If the drain hose becomes twisted and water cannot drain, your ice maker will not work. Reversing the Door Swing TOOLS NEEDED: .... in. wrench, ... in. wrench, flat putty knife, Phillips screwdriver Hinge Pin .... in. Hex Head Hinge Screw Handle Screw Endcap Screw To remove door from hinges: 1. Unplug ice maker or disconnect power. 2. Remove the handle screws and handle (on some models). Keep the parts together and set them aside. 3. Remove the hinge pin from the top hinge. 4. Remove the door from the hinges and screw the top hinge pin back into the top hinge. 5. Reverse the door endcaps as follows: ¦ Remove both the screws and endcaps (top and bottom). ¦ Place the top endcap on the bottom of the opposite side of the door with the long flat side facing the door front. ¦ Place the bottom endcap on the top of the opposite side of the door with the long flat side facing the door front. 6. Set the door aside. To reverse the hinges: 1. Unscrew and remove the top hinge. Replace the screws in the empty hinge holes. 2. Remove the screws from the bottom of the opposite side of the ice maker cabinet. Turn the top hinge upside down so that the hinge pin points up. Place the hinge on the bottom opposite side of the ice maker and tighten screws. 3. Remove the plastic hinge pin sleeve from the “old” bottom hinge and replace it on the new bottom hinge pin. 4. Remove the “old” bottom hinge screws and hinge. Replace the screws in the empty hinge holes. 5. Remove the screws from the top of the opposite side of the ice maker cabinet. Turn the hinge upside down so that the hinge pin poin...