Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
4. Allow one hour for the refrigerant to settle before plugging ice maker in. 5. The appliance must be positioned so that the plug is accessible. DANGER CONNECTING YOUR ICE MAKER ! * Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged please call customer service. 1. This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electric shock. 2. Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under any circumstances, cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician. 3. This appliance requires a standard 110~120 volt, 60Hz electrical outlet with three-prong ground. CLEANING AND MAINTAINING YOUR ICE MAKER Before using your ice maker, you are strongly recommended to clean it thoroughly. 1. Take out the ice basket. 2. Clean the interior with diluted detergent, warm water and a soft cloth. 3. The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water. 4. Dry the interior and exterior with a soft cloth. 5. When the machine is not in use, open the water drain cap to completely drain the water reservoir. 4 USING YOUR ICE MAKER USING YOUR ICE MAKER 1. Select the size of the ice cube by pressing the “Select” button. If the room temperature is lower than 60°F, it is best to select the small or medium ice size, otherwise the ice cubes might stick together. 2. Open the cover, remove the ice basket and pour water into tank. Keep water level below the level mark. 3. Press “Power” on the control panel to begin the ice making cycle. 4. The ice making cycle lasts 6 to 14 minutes, depending on the size of the ice cubes selected. 5. While the ice maker is on, verify the water level periodically. If the water level is too low, the ice maker will stop automatically, and the “Water” indicator will turn on. Press the “Power” button, fill the unit with water, and then press the “Power” button again. Allow the refrigerant inside the compressor at least 3 minutes to settle before restarting. 6. The ice maker automatically stops working when the ice basket is full. 7. Change the water in the water reservoir periodically to ensure cleanliness and hygiene. 8. It is best to use tap water or bottled drinking water in the ice maker. Distilled water may not work. If you do use distilled water and the ice maker will not function, try adding a little salt into the water (a small amount of salt added to the water should be imperceptible). 9. If the ice does not taste good, or the unit develops a musty odor, try running a few cycles of the ice maker with a mild white vinegar solution. Then empty out all the vinegar solution and run a few cycles with plain water to eliminate all traces of the vinegar. If the ice maker will not be used for an extended period of time, you should drain the water from the reservoir. TROUBLESHOOTING PROBLEM The “Water” indicator is on. The “Ice Full” indicator is on. POSSIBLE CAUSE SOLUTION Stop the ice maker, fill it with water, Low water level. and then restart it. Open the drain cap on the side of the unit and drain out a small There is some air in the amount of water. Replace the drain lines. cap and attempt to use the unit again. The unit is filled with Add a little bit of salt to the water or distilled water- or some use water from a different source other type of water with (tap water or bottled drinking water no impurities. is best). The ice basket is full. Remove ice from the ice basket. 5 The “Water” and “Ice” indicators are both flashing. The ice shovel cannot move. Check if the ice is blocking the ice pusher, otherwise, consult service. The ice cubes The ice cycle is too long. Stop the ice maker, and restart it when the ice blocks melt. Select the small ice button. stick together. The water temperature in the inner tank is too low. Change the water in the inner tank. The ideal water temperature is 45°-90°F. The compressor makes a loud The unit is being run off the wrong voltage or frequency. Plug the unit into a 110/120 Volt, 60 Hertz power source. buzzing noise The compressor was damaged in shipping. Contact the shipper. The unit does nothing Power is not supplied to the unit. Plug the unit into a 110/120 Volt, 60 Hertz power source. The ice making cycle seems The ambient temperature or the water temperature is too high. Please run the ice maker in temperatures below 90°F and/or pour colder water into tank. normal but no ice Refrigerant leakage. Consult a qualified technician. is produced. A pipe in the cooling system is blocked. Consult a qualified technician. 6 TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS & CIRCUIT DIAGRAM TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS & CIRCUIT DIAGRAM M MMo ood dde eel ll I...