Votos - 1, Puntuación media: 4 ( )

Fabricar: Poulan Tamaño del archivo: 923.39 kb Nombre del archivo: Idioma del manual:

(1) Lower Chute (1) Cover Seal • Check carton contents against list. Be sure all parts (1) Support Post (1) Bag of Parts are there. (1) Owner's Manual NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. GROUP "A" ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE BAG OF PARTS CONTENTS GROUP "B" REAR MOUNTING BRACKET AND SUPPORT TUBE TO DRAW BAR (4) Shoulder Bolt 5/16 - 18 Self Tapping SUPPORT POST TO COVER ASSEMBLY (3) Carriage Bolt 5/16 - 18 x 3/4 (3) Locknut 5/16-18 (4) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 (2) Washer 11/32 x 1-1/2 x 10 Ga. (2) Lock Washer 5/16 (2) Wing Nut (1) Support Plate NOT SHOWN FULL SIZE 4 BAG OF PARTS CONTENTS (continued) GROUP "F" GROUP "C" CHUTE LATCH ASSEMBLY to UPPER CHUTE (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Acorn #10 (1) Spacer, Split #10 (1) Rubber Latch LOWER CHUTE ASSEMBLY TO MOWER DECK GROUP "G " CHUTE LATCH ASSEMBLY to LOWER CHUTE (2) Nut, Weld #10 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Screw #10 x 5/8 (2) Latch Hook Assembly (1) Nut, Weld #10 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Screw #10 x 5/8 GROUP "D" SUPPORT POST TO MOUNTING BRACKET (1) Bracket Support Pin (1) Retainer Spring (4) Tubing End Caps GROUP "E" SUPPORT TUBE TO COVER ASSEMBLY (1) Bolt 5/16 - 18 x 3/4 (2) Locknut 5/16-18 (1) Bolt 5/16 - 18 x 2-1/4 5 6 WARNING Do notoperatemowerunlesscontainer is properlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlya recommended replacement container. WARNING Donotoperatemowerunlesscontainer isproperlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlya recommendedreplacement container. WARNING Donotoperatemowerunlesscontainerisproperlyissubjecttowearanddetierioration. Checkbagfrequently.Replace whencrackedordamaged.Useonlya recommendedreplacement container. 02079 CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in "NEUTRAL" position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. (1) 3/8" Wrench (1) 1/2" Wrench (2) 9/16" Wrenches (1) 1/2" Socket (1) Drive Ratchet (1) 3" or longer Extension (1) Short Handle Phillips Screwdriver THESE ARE THE TOOLS YOU WILL NEED TO ASSEMBLE YOUR GRASS CATCHER: NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. LOWER CHUTE ATTACHING STRAPS BEFORE YOU START TO ASSEMBLE THE GRASS CATCHER Some tractor models may need minor modifi cations before you can mount the grass catcher to the tractor. Look carefully at the drawbar on your tractor and compare to the illustrations below. If your drawbar looks like STYLE "A" (has the upper corner ribs), your tractor is ready - proceed with the grass catcher assembly. If your drawbar looks like STYLE "B" (does not have the upper corner ribs), go to the PREPARATION section in this manual. PARTS IDENTIFICATION TRACTOR DRAWBAR STYLE "A" 02320 TRACTOR DRAWBAR STYLE "B" 02321 UPPER CORNER RIBS UPPER CHUTE CHUTE LATCH DUMP BAG INDICATOR LOWER CHUTE GRASS CATCHER CONTAINERS COVER ASSEMBLY REAR MOUNTING BRACKET and SUPPORT TUBE (See Figs. 1A, 1B & 1C) Use Hardware - - GROUP "A" Before continuing with assembly, you must fi rst determine which type of drawbar your tractor is equipped with. Compare your drawbar with the illustrations of "BEFORE YOU START TOAS SEM BLE THE GRASS CATCHER" and follow instructions given. DRAWBAR WITH UPPER CORNER RIBS - STYLE "A" NOTE: If your tractor already has four (4) shoulder bolts installed on the rear drawbar, simply hang the mounting bracket, lanced tabs towards bottom, on the bolts (See Fig. 1A). 1. Assemble the support tube to drawbar as shown. From backside of drawbar place reinforcement plate so that weld screws go through holes in left side of drawbar. Place support tube over weld screws and assemble flat washer, lockwasher, and wing nut as shown Do not tighten at this time. 2. Discard remaining hardware in hardware GROUP "A". REINFORCEMENT LOCK UPPER CORNER RIBS WING NUTS 02354 LANCED TABS SHOULDER BOLTS PLATE SUPPORT TUBE FLAT WASHERS WASHERS TOWARD BOTTOM FIG. 1A If your tractor does not have four (4) shoulder bolts installed on the drawbar, follow the instructions below (See Fig. 1B). 1. Using the four formed holes in the drawbar, install the four self tapping shoulder bolts as shown and tighten securely. 2. Hang the mounting bracket, lanced tabs towards bottom, on the bolts. 3. Assemble the support tube to drawbar as shown. From backside of drawbar place reinforcement plate so that weld screws go t...

Descargar ahora

Introduzca dos números de la imagen: