Votos - 2, Puntuación media: 4 ( )

Fabricar: Electrolux Tamaño del archivo: 877.51 kb Nombre del archivo: Idioma del manual:

The exposure of threads is prohibited. 1.3 ASSEMBLING TWO APPLIANCES Fig.1 Lateral connection The assembly kit contains two of each of the following: caged nuts (1 / Fig.1) pre-assembled on the right-hand side of the appliance, hexagonal screws M8x25 (1 / Fig.1) and mounting links (2 / Fig.1) O Remove the control panels from both appliances as in 2.2 O Remove the front panels from both appliances as in 2.1 O Keeping the screw (1 / Fig.1) loose, turn it until it is approximately 5 mm deep in the caged nut. Positioning the appliances: O Place the appliances next to one other. O Align for position and height. Connect the appliances: O Fit the mounting link (2 / Fig.1) into the inside of the second appliance's left connecting plate. O Tighten the screws. Note If required, the caged nuts can also be fitted on the other side of the appliance. 62.9677.01 UL Seite 5 0] Electrolux INSTALLATION INSTRUCTIONS 1.4 SIDEWALL (D) 1.6 ASSEMBLING ON CASTORS Fig.2 Assemblage of sidewall The assembly kit contains two of each of the following: hexagonal screws M8x25 (1 / Fig.1), bolts with retaining rings (2 / Fig.1), mounting links (3 / Fig.1), hexagonal screws M8x16 with serrated washers and hexagonal nuts M8, hexagonal screws M5 with serrated washers (4 / Fig.2) and a fastening angle (5 / Fig.2). O Insert the bolts with the retaining rings (2 / Fig.1a) from outside into the guide in the sidewall. O Keeping the screw (1 / Fig.1a) loose, turn it until it is approximately 5 mm deep in the pre-assembled caged nuts in the sidewall. O Attach the fastening angle (5 / Fig.2b) to the bottom of the frame using the screws, serrated washers and nuts. ^ (4 / Fig.2). O Position the sidewall and screw it on from below using two hexagonal screws and the serrated washers. O Fit the mounting link (3 / Fig.1b) into the inside of the appliance's connecting plate. O Align the sidewall and firmly tighten all screws. 1.S STEEL PLINTH ^ (3) m b* a) (Э) (1) Í Fig.4 Assemblage on castors The assembly kit for mounting on castors contains two cross bars (2/Fig.4a) each with a fixed rear wheel (1/Fig.4a) and a turnable front wheel (3/Fig.4a). Mounting the castors: O Put the appliance on supports. O Remove the feet; each is tightened with four screws (Fig.4b). O Bring the two cross bars into the correct position below the appliance and fasten it with 8 screws arrows (Fig.4a). O Remove the supports. O Fasten the appliance to the building. Use the hole to attach a chain descending from the wall (arrow/Fig.4c). Making sure the chain is shorter than the gas and electric connections. Note: Appliances on wheels must be secured by fasten it to the building. 2. ACCESS TO INTERIOR Note: Only authorized technicians may access the interior. Fig. 3 Plinth assembly To assemble the plinth you will need: • Right and left side plinth (1 / Fig.3). • Plinth for the front and, for free-standing appliances, for the rear also (2 / Fig.3). O Push the side plinth (1 / Fig.3) onto the legs from front to rear using the fastener. The larger gap (b / Fig.3) on the fastener must be at the bottom. O Affix the fasteners (3 / Fig.3) to the plinth (2 / Fig.3). O The larger gap (b / Fig.3) on the fastener must be at the bottom. O Attach the plinth with the fasteners (3 / Fig.3) onto the feet. b a b Seite 6 62...

Descargar ahora

Introduzca dos números de la imagen: