Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Vulcan-Hart Tamaño del archivo: 1.12 mb Nombre del archivo: Idioma del manual:

UNPACKING Immediately after unpacking, check for possible shipping damage. If the pasta cooker is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Do not use the door or its handle to lift or move the pasta cooker. For pasta cookers shipped on a pallet: Before removing the cooker from the pallet, assemble casters or legs (see ASSEMBLY in this manual). The pasta cooker is shipped without the swivel head attached. Look for the swivel head in the tank of the cooker and screw it onto the faucet before hooking up the water. LOCATION Do not install pasta cooker next to a deep fat fryer because a splash-over of water into the hot oil may cause a flash fire. The equipment must be kept free and clear of combustible substances. The pasta cooker, when installed, must have minimum clearance from combustible construction of 6" (152 mm) from the sides and 6" (152 mm) from the rear. Clearance requirement from non-combustible construction is 0" at the sides and rear. The pasta cooker may be installed on combustible floors. The installation location must allow adequate clearances for servicing and proper operation. A minimum front clearance of 36" (914 mm) is required. The pasta cooker must be installed so that the flow of combustion and ventilation air will not be obstructed. Adequate clearance for air openings into the combustion chamber must be provided. Make sure there is an adequate supply of air in the room suitable for the amount of combustion gas feeding the burners. Do not permit fans to blow directly at the pasta cooker. Avoid open windows next to the pasta cooker. Avoid wall-type fans which create air cross currents within the room. – 5 – INSTALLATION CODES AND STANDARDS Your Vulcan-Hart gas pasta cooker must be installed in accordance with: In the United States of America: 1. State and local codes. 2. National Fuel Gas Code, ANSI-Z223.1 (latest edition), available from the American Gas Association, Inc., 1515 Wilson Blvd., Arlington, VA 22209. 3. National Electrical Code ANSI/NFPA-70 (latest edition). Copies may be obtained from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. In Canada: 1. Local codes. 2. CAN/CGA-B149.1 (latest edition) Natural Gas Installation Code. 3. CAN/CGA-B149.2 (latest edition) Propane Installation Code, available from the Canadian Standards Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3. 4. Canadian Electric Code, CSA Standard C22.2 No.3 (latest edition). Copies may be obtained from The Canadian Standards Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3. ASSEMBLY The cooker must be restrained to prevent tipping when installed in order to avoid the splashing of hot liquid. The means of restraint may be the manner of installation, such as connection to a battery of appliances or installing the cooker in an alcove, or by separate means, such as adequate ties. Legs 1. Position the pasta cooker in an open space near the final installation area. 2. Tilt pasta cooker on its side. Be careful not to scratch the finish. 3. Thread legs into mounting holes provided on the bottom of the pasta cooker by screwing in a clockwise rotation until tightened. 4. Carefully raise pasta cooker to its normal position and place it in the installing location. – 6 – Casters 1. Position the pasta cooker in an open space near the final installation area. 2. Tilt pasta cooker on its side. Be careful not to scratch the finish. 3. Thread casters into mounting holes provided on the bottom of the pasta cooker by screwing in a clockwise rotation until tightened. 4. Carefully raise pasta cooker to its normal position and place it in the installing location. NOTICE: When the pasta cooker is mounted on casters, it must be installed with the casters supplied, a connector (not supplied by Vulcan-Hart) complying with either ANSI Z21.69 (latest edition) or CAN/ CGA-6.16 (latest edition), and a quick disconnect device complying with either ANSI Z21.41 (latest edition) or CAN1-6.9 (latest edition). It must also be installed with restraining means to guard against transmission of strain to the connector, as specified in the appliance manufacturer's instructions. Attach the restraining device at the rear of the oven. (Fig. 1). Provide a gas line strain relief to limit movement of the pasta cooker without depending on the connector and any quick-disconnect device or its associated piping to limit the pasta cooker's movement. Attach the strain relief to the rear of the pasta cooker (Fig. 1). Should it be necessary to disconnect the gas line strain relief, turn off the gas supply before disconnection. Reconnect this restraint before turning the gas supply on and returning the pasta cooker to its installation position. STRAIN RELIEF FITTING FOR GAS LINE THIS SIDE ONLY. (Strain relief fitting supplied by Vulcan-Hart. Chain to be supplied by others.) PL-51493 Fig. 1 Instructions for installing casters to the pasta cooker...

Descargar ahora

Introduzca dos números de la imagen: