Votos - 4, Puntuación media: 4 ( )

Fabricar: Henny Penny Tamaño del archivo: 950.52 kb Nombre del archivo: Idioma del manual:

SAFETYALERT SYMBOL is used with DANGER, WARNING, or CAUTION which indicates a personal injury type hazard. NOTICE is used to highlight especially important information. CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. The word WARNING is used to alert you to a procedure, that if not performed properly, might cause personal injury. 1-2 103 Model HCS-2/HCW-3/HCW-5/HCW-8 SECTION 2. INSTALLATION 2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny Heated Display Cabinet. Installation of this unit should be performed only by a qualified service technician. Do not puncture the skin of the unit with drills or screws as component damage or electrical shock could result. 2-2. UNPACKING The Henny Penny Heated Display Cabinet has been tested, inspected, and expertly packed to ensure arrival at its destination in the best possible condition. The cabinet has been bolted to a wooden skid. All glass items have been packed in cartons and taped inside the unit and the doors taped shut. The unit is then packed inside a triple wall corrugated carton with sufficient padding to withstand normal shipping treatment. Step 1 Any shipping damages should be noted in the presence of the delivery agent and signed prior to his or her departure. To remove the Henny Penny Heated Display Cabinet from the carton, you should: 1. Carefully cut banding straps. 203 2-1 Model HCS-2/HCW-3/HCW-5/HCW-8 2-2. UNPACKING (Continued) 2. Open top flaps and remove packing. Step 2 3. Lift carton off skid. Step 3 4. Remove four bolts from under skid. Step 4 The unit is now ready for location and set-up. 2-2 103 Model HCS-2/HCW-3/HCW-5/HCW-8 2-3. LOCATION Place the unit on a table, preferably with a cut-out opening below the cabinet to allow easy service connections and serviceability. When setting up the Henny Penny Heated Display Cabinet, be sure to level the table. The unit has built-in draining capabilities, but this becomes ineffective when set on an unlevel table. After the Henny Penny Heated Display Cabinet has been leveled on the table, run a bead of silicone rubber (silicone or equivalent sealant must be a NSF listed material) around the perimeter of the unit sealing it to the table top. You are now ready to make the electrical and drain connections to the unit. 2-4. REMOVE CONTROL END 1. Remove the seven screws fastening the end panel to the cabinet. PANEL 2. Slide bottom of end panel out first allowing top to drop below shelf edge. Step 2 103 2-3 Model HCS-2/HCW-3/HCW-5/HCW-8 2-5. DRAIN CONNECTION The drain can be connected to a 1 inch N.P.T. directly below the water well or to a 3/4 inch N.P.T. from the operator’s side. We recommend the 1 inch N.P.T. connection as this will allow straight down draining of the water. 2-6. ELECTRIC CONNECTION The heated display cabinet is available from the factory wired for 208 or 230 volts, single phase, 3-wire (includes neutral) or three phase, 4-wire (includes neutral) 50 or 60 Hz. service. The proper power service cable must be provided at installation. Check the data plate on the side panel of the control end to determine the correct power supply. To avoid electrical shock, the cabinet must be adequately and safely grounded (earthed) according to local electrical codes. (FOR EQUIPMENT WITH CE MARK ONLY!) To prevent electric shock hazard this appliance must be bonded to other appliances or touchable metal surfaces in close proximity to this appliance with an equipotential bonding conductor. This appliance is equipped with an equipotential lug for this purpose. The equipotential lug is marked with the following symbol A separate disconnect switch with proper capacity fuses or breakers must be installed at a convenient location between the cabinet and the power source. The field supply wiring to the cabinet should be an insulated copper conductor rated for 600 volts and 90°C. 2-4 1004 Model HCS-2/HCW-3/HCW-5/HCW-8 2-6. ELECTRICAL CONNECTION The electrical power can be connected from the bottom or from the (Continued) operator’s side. There is a 1-3/32 inch diameter hole for either connection. Again, we recommend the bottom connection as this will give a cleaner appearance to the unit. Please observe the electrical connection information on the data plate located on the side panel of the control end. Voltage potential of L1 and L2 to ground cannot exceed 125 volts, or damage to the unit could result. 2-7. ELECTRIC DATATABLE Model Volts Phase Watts Amps HCW-2 120/230 1 760 4.7 HCW-2 120/208 1 760 4.9 HCS-2 230 1 2852 12.4 HCW-3 120/230 3 3400 10.7 HCW-3 120/230 1 3400 16.3 HCW-3 120/208 3 3400 11.5 HCW-3 120/208 1 3400 17.6 HCW-3 400 3 3400 5.0 HCW-5 120/230 3 4160 12.2 HCW-5 120/230 1 4160 18.0 HCW-5 120/2...

Descargar ahora

Introduzca dos números de la imagen: