Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The conversion should be done by a qualified electrician. REFER TO N.E.C. (NATIONAL ELECTRIC CODE AND LOCAL CODES) 115 VAC ONLY ACC. SWITCHSYSTEM SWITCH BOND BAR THERMOSTAT FIELD WIRING JUNCTION BOX TIMER CIRCUIT PROTECTOR BUTTON BUTTON AIR BLOWER SELECT TOGGLE SWITCH PLUG-IN CONNECTORS GFCI OPERATION Basic Control Set-Up (Continued) • Open the skirt door giving access to the electrical cabinet. • Your spa is provided with a ground fault circuit interrupter (GFCI). At initial start-up and at least once a month thereafter, with the plug connected to power, push the test button located on the spa electrical panel. The reset button should pop out. Push this button in to reset. If the interrupter fails to operate in this manner, there is a ground current flowing or a device malfunctioning, indicating the possibility of electric shock. Disconnect the plug from the receptacle and do not use the spa until the source of the breakdown has been identified and corrected. • Make sure the circuit protector buttons are pushed in. • Locate the HIGH TEMPERATURE SAFETY SWITCH, which is a raised button on the end of the heater. Push this button to be sure it is in the reset mode. The purpose of this switch is to shut down the spa if the water becomes excessively hot. If, for some reason, the switch is tripped, the reset button must be pushed in for the heater to operate again after the water has cooled to about 90°F. • Set the built-in timer (see below). • Close the redwood skirt door. HIGH TEMPERATURE SAFETY RESET BUTTON Setting the Timer The built-in 7-day timer is located in the electrical cabinet. The tooth-like tabs that are located on the dial can be set to activate the filter system for two-hour periods on any day(s) of the week. First set the correct time. Set the time of day by rotating the outer dial and aligning the correct time with the small arrow in the inside of the dial. Note: both correct time and day must be set. Next slide one of the tabs toward the center of the dial at the time at which you wish the filter system to operate. Note that the timed mode can begin at any time of day or night on any specified day of the week. TIMER PUSH IN ONE TAB FOR EACH TWO HOUR PERIOD OF OPERATION Mo nday Tuesday WednesdayThursday Friday Saturday Sunday OPERATION Controls A switch panel giving you convenient control of the jets, filter, heater/filter, light and air blower is located on the spa rim. To ensure your safety and allow easy operation, your spa is equipped with two air-activated switches. One, the SYSTEM switch, controls the whirlpool jets, heat, and filtration. The other switch, ACC (Accessory) controls the air blower and optional light. Refer to the Control Panel illustration for an explanation of the various switch functions. SYSTEM The SYSTEM switch controls the following four functions in the continuous sequence indicated: 1. OFF 2. JETS 3. HTR/FILTER 4. FILTER (The next selection is OFF again.) Use the JETS function as a reference to indicate your location in the function sequence, since that function is the most obvious when operating. For best performance and increased equipment life, pause a second or two between push-button selections. Not pausing may cause the switch to malfunction. CONTROL PANEL ACC (Accessory) The ACC (Accessory) switch controls these functions in the continuous sequence indicated: 1. OFF 2. AIR 3. AIR/LIGHT 4. LIGHT When the AIR (blower function is activated, thejets will tyrn off if they have been selected by the SYSTEM switch. Activating the AIR function will also turn off the heater if the HTR/FLTR function has been activated by the SYSTEM switch. (If the unit is properly converted to 230 VAC 50 Amp, 4—wire, no overriding of features will exist.) SYSTEM ACCESSORY TEMPERATURE CONTROL KNOB SWITCH SWITCH SILENT AIR INDUCTION CONTROLS TEMPERATURE CONTROL KNOB SYSTEM SWITCHAIR INDUCTION HEATERSYSTEM JETS FILTER HTR/FLTR OFF HEATER INDICATOR LIGHT (Controls Air Blower (Controls Whirlpool, Heater/ (for adjusting thermostat) and Light Functions) Filter and Filter only functions.) OPERATION Temperature Control Turn on the heater by selecting the HTR/FILTER mode with the SYSTEM switch. With this selection, you can verify that the spa’s heater is operating by viewing the indicator light on the spa control panel. Set the HEATER knob by rotating it to the desired temperature. When the water temperature is lower than that set by the HEATER knob, the heater and filter pump will be activated. The heater will automatically turn off when the desired temperature is reached. When the heater is on, the water is also being filtered. The heater is designed to maintain a minimum temperature of approximately 45-50°, its lowest setting. This does not necessarily protect the spa from freezing. See page 16 for winterizing procedures.. The Temperature Control is designed to maintain a minimum temperature of approximately 45 -50°, its lowest setting. This does not necessarily protect the spa from freezing. Se...