Iniciar sesión:
Votos - 2, Puntuación media: 3.5 ( )

Manual de usuario Kohler, modelo VINTAGE K-7158

Fabricar: Kohler
Tamaño del archivo: 98.74 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Be careful not to scratch the surface of the product. 7. INSTALL THE WOOD RIM NOTICE: The wood rim must be installed to the bath before any framing is built around the bath. Do not use this wood rim in sunken installations. Install the bath, and make the drain connections. Use two people for this procedure. Hold the wood rim in position under the bath rim. Install the angle brackets to the wood rim, as illustrated, using #10 x 3/4” round-head screws. The holes are pre-drilled in the wood rim. Apply a bead of clear silicone sealant, as shown. CAUTION: Option for using silicone sealant: Do not let the bath rest on the rim, or damage to the wood rim and the bath will result. The bath must be supported by the legs. Install the bolts into the angle brackets, as shown, to install the wood rim to the bath. Loosely assemble all the components. Tighten the bolts when they are threaded into the bosses on the underside of the rim. The bath is now ready for framing, and the installation of the wall material. NOTE: The bottom of the wood trim Option for using silicone sealant: be sealed with a bead of clear silicone sealant. 8. INSTALL THE TOWEL BAR Attach the two end brackets to the bath rim with washers and bolts. Carefully slide the two support brackets on the towel bar. Do not scratch the towel bar. Position one end of the towel bar into an end bracket, and attach the support brackets to the bath rim with washers and bolts. Only handtighten the bolts at this time. Fit the other towel bar end into the remaining end bracket. Align as needed. Tighten all bolts. Secure the towel bar to all the brackets with setscrews. Repeat for the other towel bar. Kohler Co., Kohler WI U.S.A. 6 110050-2-AB 9. INSTALL THE BATH A. WHIRLPOOL SET-IN Corner or Recessed Installations: Move the whirlpool into position. Insert the drain tailpiece into the trap. Level the whirlpool by fitting metal shims under the whirlpool feet, as needed. The whirlpool must be level and resting on all four feet. Check for level along the top of the whirlpool, and across the drain side. If the feet are not accessible from the back or side, move the whirlpool in and out of position until it is shimmed properly. Metal Shims Metal Shim Option For Sunken Installation: Set the bath into the sunken installation. Make sure the unit is level and resting on all support feet. Insert the drain tailpiece into the trap. Apply a bead of silicone sealant under the rim of the unit. B. INSTALL PLUMBING A l. CAUTION: Risk of property damage. Ensure a watertight seal on the whirlpool drain connections. Connect the drain to the trap according to the drain manufacturer’s instructions. NOTE: An access panel will simplify future maintenance. Connect Here 2. Install the faucet valving and spout tee. Open the hot and cold water valves, and check the supply connections for leaks. 3. Run water into the bath, and check the drain connections for leaks. 110050-2-AB 7 Kohler Co., Kohler WI U.S....

Otros modelos de este manual:
Otros accesorios para la casa - VINTAGE K-700 (98.74 kb)
Otros accesorios para la casa - VINTAGE K-7159 (98.74 kb)
Otros accesorios para la casa - VINTAGE K-1172 (98.74 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría