Lumens Tubes Lumens at per Tube per Box Light Box Surface LB1218 650 1 F15T8 650 LB1620 650 2 F15T8 1300 LB1824 650 2 F15T8 1300 LB2436 1750 3 F30T8 5100 All electrical components are U.L. listed. 4. Remove the hold-down screws and lift off the light diffusers. 5. Remove and replace fluorescent tubes. 6. Return diffusers, glass and Plexiglas panels to their original positions. Re-install aluminum strips and screws. T y Alvin & Company, Inc. Bloomfield, CT Grand Prairie, TX www.a

For your own safety, use gloves when handling glass. Place the glass on top of the Plexiglas sheet and replace the aluminum strips. 2. To operate, depress the on/off switch and hold for one or two seconds until the lights illuminate. Note: Bulbs may loosen during shipping. If bulbs don't illuminate check that they are properly seated in fixture. 3. The Satin-Glow Lightbox is designed to operate on 110V AC, 60 cycle. Please do not use any other power source. 4. Removal of the back panel or tam

Always use direct replacement lamps in order to prevent overheating. 2. Disconnect the power cord. 3. Remove the screws and aluminum strips from the top surface of the lightbox. Carefully remove glass and Plexiglas panels. Degrees of Illumination MODEL No. Lumens Tubes Lumens at per Tube per Box Light Box Surface LB1218 650 1 F15T8 650 LB1620 650 2 F15T8 1300 LB1824 650 2 F15T8 1300 LB2436 1750 3 F30T8 5100 All electrical components are U.L. listed. 4. Remove the hold-down scr

For your own safety, use gloves when handling glass. Place the glass on top of the Plexiglas sheet and replace the aluminum strips. 2. To operate, depress the on/off switch and hold for one or two seconds until the lights illuminate. Note: Bulbs may loosen during shipping. If bulbs don't illuminate check that they are properly seated in fixture. 3. The Satin-Glow Lightbox is designed to operate on 110V AC, 60 cycle. Please do not use any other power source. 4. Removal of the back panel or tam

XII-4-XB Tools Required: Phillips screwdriver, drill with VW bit. Parts Included: A 1pc Leg Frame B 1pc Tabletop C 2pcs Rear Extension Tubes (Shipped in separarate box) : D 2pcs Front Extension Tubes F 2pcs Height Adjustment Knobs To Assemble: Unpack all parts and inspect to confirm that all are present. Unfold base (A). Insert rear extension tubes (C) completely into frame (A) and loosely hand-tighten knobs (F). Insert front extension tubes (D) into frame (A). Place table top (B)

Align holes in front leg extensions (D) with holes in table top as shown in Figure 1. Fasten all 1/2" screws (H) and tighten securely. Use care not to overtighten and strip. Carefully return table assembly to the upright position. Adjust table top to desired height using height adjustment knobs (F). You’re finished and your table is ready to use as shown in Figure 2. Folding Table: Drop all extension tubes down to their lowest positions. Lift top up until the front extension tubes (D) diseng

Carefully insert two front extension tubes (F) with attached brackets facing out. All four extension legs should be at their lowest position and locked with four height adjustment knobs (H). Set base aside. Front extension tube Figure 4 Figure 3 Place tabletop (B) with preferred side facing down on carpeted or protected floor. Place supplied cardboard template on board surface with edge of template at front edge of board. Left and right edges of template should be an equal distance from each

Make sure ends of back panel are snug against steel leg frames and holes are aligned in steel flange with pre-drilled holes in back panel. Attach using four 5/s" screws (I) supplied. Repeat step for right leg frame. Figure 2 5/s" Screws Floor Glide Figure 1 5/s" Screws □ Carefully remove base assembly from table/bench and place upright on floor. ^9 Place shelf (D) with predrilled holes facing up on the bench/table with 15 ends hanging over edge. Lift base assembly carefully (may require

For best results, we suggest that you tighten the four Allen bolts in sides of main easel frame, as shown in Figure 1, and tighten the two Phillips screws in the back of canvas support assembly, as shown in Figure 2. 2 Lay main easel frame flat on floor with brass height adjustment track facing up. □ Carefully slide canvas support assembly from below into slots and tracks in main frame, as shown in Figure 3. Pull spring-loaded height-adjustment ring and set in the third track position for th

WTF35 B C E CONTENTS Key Qty. Description A 1 Grid Tray with small openings B 1 Frame Section with rubber feet C 2 Grid Tray with large openings D 1 Frame Section E 2 Covered Casters with lock nuts F 2 Side Braces (left and right) G 1 Dust Protector bottom cover (Optional) 12 Nuts, 4 Screws 1. Attach grid tray with small openings(A), to bottom of large frame section(B). 2. Attach remaining two trays(C). 3. Secure smaller frame section(D) in the same manner. 4. Using encl