Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
3 figure 5. general inventory. i J n o p M l K W V Q U t r S Xy if any nonproprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements drum be obtained at your local hardware store. -13 Site Considerations Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest work- piece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine. Space Allocation Consider the largest size of workpiece that will be processed through this machine and provide enough space around the machine for adequate operator material handling or the installation of auxiliary equipment. With permanent installations, leave enough space around the machine to open or remove doors/covers as required by the maintenance and service described in this manual. See below for working clearances. Children or untrained people may be seriously injured by this machine. Only install in an access restricted location. Physical Environment The physical environment where your machine is operated is important for safe operation and the longevity of its components. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous chemicals, airborne abrasives, or extreme conditions. Extreme conditions for this type of machinery are generally those where the ambient temperature range exceeds 41°–104°F; the relative humidity range exceeds 20–95% (non-condensing); or the environment is subject to vibration, shocks, or bumps. Electrical Installation Place this machine near an existing power source. Make sure all power cords are protected from traffic, material handling, moisture, chemicals, or other hazards. Make sure to leave access to a means of disconnecting the power source or engaging a lockout/tagout device. Lighting Lighting around the machine must be adequate enough that operations can be performed safely. Shadows, glare, or strobe effects that may distract or impede the operator must be eliminated. 30" 40" figure 6. Minimum working clearances. -14 Model g0703 (Mfg. since 8/09) 6. position the stand onto the dust collector assembly housing, and install one 5.16"-18 x 11.2" hex bolt and flat washer on each side of the stand at the to serve as pivot bolts (see figure 9 for To assemble your dust collector, do these location). steps: 7. Using a 5.16" wrench, snug both hex bolts. 1. invert the stand, place one 3.8" lock washer on four caster wheel studs, and thread each caster stud into the stand (figure 7). 2. Using a 3.8" wrench, tighten each caster stud. 8. With the help of an assistant, lift up on the stand and rotate the dust collector into place where the other six mounting holes line up with the stand as shown in figure 10. 9. install the remaining six 5.16"-18 x 11.2" hex bolts and 5.16" flat washers, and tighten all hex bolts. figure 7. Stand and caster wheels. 3.rotate the stand to the upright position. 4.Using the h-supports, (16) 5.16"-18 x 3.4" hex bolts, and 5.16" flat washers; install the upper rails onto the stand, as shown in figure 8. 5.Using a 5.16" wrench, tighten the hex bolts. pivot Bolt location on Both Sides figure 9. installing stand. h-Support figure 8. installing stand rails. figure 10. dust collector and stand positioning. three holes on Both Sides -15 Model g0703 (Mfg. since 8/09) 10. With the help of an assistant, raise the dust 12. Attach the casters to the bottom of the drum collector to the upright position, and install using (4) 3.8"-16 hex nuts, (4) 3.8" flat washers, the handle (figure 11) with (4) 5.16"-18 x 3.4" and (4) 3.8" lock washers (figure 13). hex bolts and 5.16" washers. figure 11. installing the hand rail. figure 13. dust collection drum casters installed. 11. Engage the filter-element crank (figure 12) with the shaft, and secure it in place with one 5.16"-18 x 3.4" hex bolt and one flat washer. figure 12. Filter-element crank installation. 13. Attach the lid latches to the side of the drum extender using six #10-24 x 3.8" phillips head screws and #10-24 nuts as illustrated in figure 14. Note: To avoid bag snags, face the screw heads located inside of the drum with the shanks facing outward, as illustrated in Figure 14. figure 14. lid latch installation. -16 Model g0703 (Mfg. since 8/09) 14. place the drum extender onto the drum so 16. place the dust bag seat into the duct collecone latch is oriented with the drum spout as tion drum as illustrated in figure 17. shown in figure 15. figure 15. drum extender and spout alignment. figure 17. installing the dust collection bag seat. 17. insert the rubber seal over the top lip of the 15. Secure the drum extender to the drum with drum rim (figure 18). pay special attention the drum clamp (figure 16), ...